-
This community needs YOUR help today. With the ever increasing fees of everything (server, software, domain, e-mail) , we need help. We need more Supporting Members, today. Please invest back into this community to help spread our love and knowledge of IH Cub Cadets. You get a lot of great new account perks including access to private forums. If you sign up for annual, I will ship a few IH Cub Cadet Forum decals too in addition to all the account perks you get. You can see what it looks like below.
Sign up here: https://www.ihcubcadet.com/account/upgrades
New member. Hello & 1250 headlight help needed
- Thread starter Gary Hall
- Start date
Help Support IH Cub Cadet Tractor Forum:
Gary Hall
Member
Hello, new member from S. Central Virginia. I just got a (late 70s?) 1250 Cub. I'm adding headlights and need help, if someone has this or similar model I'd like to run wires like factory had them.
Large ring terminal I assume ground and where does it go? Power my guess to push-pull switch, wired to one side ammeter? Was there a fuse?
Thanks. A few pictures would explain it all.
Large ring terminal I assume ground and where does it go? Power my guess to push-pull switch, wired to one side ammeter? Was there a fuse?
Thanks. A few pictures would explain it all.
Attachments
Gary, WELCOME!
Here's a couple of photos, I had these on my laptop, they are of a 1450 that I have. I'll see if I can find more. I may have to take some photos tomorrow when I am at the family farm where this tractor is stored.
Rotary switch below and to the left of the key switch:
Here's a couple of photos, I had these on my laptop, they are of a 1450 that I have. I'll see if I can find more. I may have to take some photos tomorrow when I am at the family farm where this tractor is stored.
Rotary switch below and to the left of the key switch:
glippert
Well-known member
Welcome, Fuddy! Kraig's pics show the lights are grounded under a hood hinge bolt, and the hole you identified is, indeed, for a fuse for the lights. But it doesn't uses a push/pull switch - that gray knob below the ignition key in Kraig's pic is a two position (off/on) rotary switch. And, yes, the power comes from the negative side of the ammeter, through a fuse and the switch.
Welcome. Nice looking tractor.
There should be a breakout bundled in the harness under the dash for the lights.
Gary Hall
Member
Thanks so much! I should have looked at the instruction label below switches 
.
I see a couple switches for sale on ebay, knob style. There's a knock-out plug for the switch.
For the time being I'll probably install this push pull switch where fuse hole is, with fuse holder in line at power source. It looks like factory used 1/4" spade terminals on rotary switch posts.
.I see a couple switches for sale on ebay, knob style. There's a knock-out plug for the switch.
For the time being I'll probably install this push pull switch where fuse hole is, with fuse holder in line at power source. It looks like factory used 1/4" spade terminals on rotary switch posts.
Attachments
Welcome aboard Gary. Yes on the 1/4" spade, in a insulated block. After you like the lights, you might consider going OEM on the switch. I would call factory switches "Severe Duty" as there is vibration in the tractor from drives, mowers, engine, plus being exposed to outdoor conditions and lots of dust at times. The factory ones are robust and pretty well sealed up. CCSpecialties has reasonable pricing on them that is pretty competitive for what you get.
Welcome.
mgerecke
Well-known member
Welcome Gary. I did the same conversion and added tail lights as well. The harness is already there for the rear lights. It’s under the tunnel cover and just plug into it. Usually bundled up there with the plug in end there. Nice looking 1250
Here's two more photos of my 1450 that might be helpful. I tried to get some of the wiring under the dash but there's too much in the way.
Better view of the head light panel area:
The lower right grill mounting bolts with wire clips (I'm not certain if the large ground wire is stock or if it was added by a PO?):
Better view of the head light panel area:
The lower right grill mounting bolts with wire clips (I'm not certain if the large ground wire is stock or if it was added by a PO?):
glippert
Well-known member
Pretty sure that's stock, as it's the same on my grandson's 1250 and my 1450 & 1650.
tkhoffman
Well-known member
You got the Push-Pull switch so use it. However, make sure it pulls out without hitting the floorpan. Also keep in mind that switch will easily welcome in moisture. Internal contacts may fail on the short term with a garage or she'd kept tractor. I had a bucket load of off/pull/pull farther switches like the one you show. They lasted two years before I swapped out for a new one, opened up and cleaned the tarnished non working one.
Welcome Gary!
