Archive through October 09, 2009

[lpalma]

For Sale

Cub 107

The good..

Runs good with no knocks or funny noises
Replaced drive cup and pin in drive shaft
PTO works
No slop in the steering.Newer left spindle.
Hood is strait and not dented
S/G charges and no noisy bearings
It does come with the rear reflectors

The bad

Trunion is worn
Left font tire goes flat after a few weeks
Could use a new wire harness(it has a few jumpers)
No seat cover.
Missing drive shaft cover.
I also have a mower deck and mule drive sold separately.
$350.00 OBO...I will be willing to go lower on the price.

 

[kredlinger]

Cleaning out shop, a bunch of small cub parts. Taillights with lamps & sockets in great condition $35. Hood ornament from a 100 $15. Reproduced plastic 82 series ornament $15. Drive hub $10 all other stuff under $5 ea. OR $100 for all of it SHIPPED to your door from Eastern Iowa

 

[mdechristopher]

48 inch original cub cadet spring cultivator it will fit any cat o hitch $200.00

 

[taweivoda]

Price Reduction. The 124 with a 38" mower, the very nice complete IH Windbreaker, top, back curtain, 42" blade, new chains that was posted here on September 25 has been reduced to $575.00 picked up in SE Minnesota. 507-272-1807 if you have any questions.

 

[mpatterson]

Can that cultivator be converted into a sleeve hitch design?? Anyone ever tried that or just way too much fabricating needed? Would still work as effective or would there not be enough rise on it to get it out of the ground? That brings on another question - is a sleeve hitch and a regular cat 0 3pth have the same amount of travel when raising and lowering implements?

 

[mromano]

This is the last of my cub stuff for sale. The manual aare in very good coodition the cover on the tractor parts manual TC 113 is a little loose at the bottom. The equipment parts CPE 2 book is ok. 40.00 for the pair
The wheels are from wide frame with 3/4 axle. one also has the part number inside the other need a set of bearings. 25.00
I a lso have a set of wide frame front spindels with the axle sleeve that are in very good condition. 20.00
These prices are plus shipping

 

[mromano]

Here are a pic of the wheels

 

[rware]

582 Cub Cadet runs great, new paint,decals,seat.
located in West Virginia.

 

[mstetar]

price?

 

[rware]

I am asking $800.00 for the 582, reason for selling is I recently purchased a 2072,witch gives me 6 Cubs and Iam runnuing out of room

 

[mmiller]

Briggs Diahatsu Vanguard 3 cyl water cooled Turbo diesel. This engine is rated at 31HP @ 3600RPM, and 51ft.lbs. torque @ 2400RPM. It is missing the starter (available on Ebay @ $139) and needs an oil pickup tube for the turbo ($65 from Briggs).

It's approx 16"long x 18" wide x 16" tall and weighs 200lbs.

The non turbo version of this engine is sold at Northern for over $5000.

I was going to use this on an articulated loader but I've got a new project and need to fund it.

$500 picked up in Richmond, VA. I will hold it indefinately if paid for now.
[email protected]

 

[bbrigham]

I know, this is the wrong place but....

 

[mmiller]

I forgot to mention that the diesel I listed comes with a Briggs service manual, owners manual and parts list.

 

[krandall]

Decided to sell off most of my Cubs along with all the spare parts I've collected over the years.
I'm starting with a 1964 70 ser#84347.I bought this with visions of restoring it but have no time...It runs great but it will have a different S/G onit as this one is not working correctly...$500.00 as pictured

 

[krandall]

Also sellin my Cub with rear PTO ser#86791..Hood says 100 but it P.O. installed a N.O.S. 8hp in it.I took this tractor to most of Blunier's P.D.'s just to ride around on...The grill is missing now but otherwise it comes like you see with perfect fenders and near perfect seat $600.00

 

[mmiller]

The Briggs diesel has been sold. Thanks for all the responses.

 

[lpalma]

I have 3 Grote tailght lenses for trade or sell..
These are the correct ones for your cub.
$10.00 each,plus you get the white gasket that goes with it.Shipping is a flat rate of $4.00
I could use a carb rebuild kit,or a hydro filter..

 

[krandall]

I've got a custom made front weight set for a wide frame...14 weights at 10 pounds each...
This has been on my 149 at all of the Plow Days..
I was going to paint it but never got around to it....$150.00

 

[krandall]

I've also got a pair of suitcase weights but have no idea what they fit....
14 1\2 inches tall x 11 1\2 inches wide x 2 3\4 thick..opening is 4 1\2 inces deep and slot is 1wide x 7 3\4 long..weight is 65 pounds each
100.00 for the pair

 

[lpalma]

I only have 1 tailight lense left!!
Thanks