• This community needs YOUR help today. With the ever increasing fees of everything (server, software, domain, e-mail) , we need help. We need more Supporting Members, today. Please invest back into this community to help spread our love and knowledge of IH Cub Cadets. You get a lot of great new account perks including access to private forums. If you sign up for annual, I will ship a few IH Cub Cadet Forum decals too in addition to all the account perks you get. You can see what it looks like below.

    Sign up here: https://www.ihcubcadet.com/account/upgrades

Search results

kirk engines
cadet connection
xtreme motor works
shop deals on amazon
IH Cub Cadet Tractor Forum

Help Support IH Cub Cadet Tractor Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. J

    6" pto for a M18/M/20.Is it the same for the Kohler command engines?

    I have a 451 snowblower and a 54" deck that both were used w/a 6" pto.I have the 4.5" pto on a m18 Will a 6" pto fit on this engine and a command engine since they are discontuning making parts for this engine?
  2. J

    Front axle spindle bushing for an 1882

    I had the get a whole axle. When I took mine apart the L/S bushing was spinning in the bore.I was hoping the spindle was bad.So much for thinking.
  3. J

    How to tell what snowthrower I have/What's the difference in the 4.5" & 6" pto drives

    Ok so I've disassembled the blower and know that I have a 451 because of the gear ratio.I have found the bottom driven gear for the 450 which is 28t now I'm trying to locate a top gear which is 15t otherwise I'll have to do it w/a pulley.I'm also in need of the the 2 plates that extend the...
  4. J

    What's the difference in the 4.5" & 6" pto drives

    I'm going to go to the newer 54" deck and those machines all have 6" pto's.My cub uses the 4.5" pto.Will this work or does this deck need the 6" pto to work right
  5. J

    How to tell what snowthrower I have/What's the difference in the 4.5" & 6" pto drives

    Ok I'll get some posted.Thank You
  6. J

    1882 reverse soft?

    I've used the tractor for about 2 tanks of gas and reverse works fine.I did find that between the 2 pump unit's I have that 1 of the valves was an different design maybe an older stlye?No leaks works great
  7. J

    Switching to cv jt driveshaft in a 1572 how hard is it?

    Necessity is the mother of all invention.As the parts run out we will all need to more inventive.
  8. J

    How to tell what snowthrower I have/What's the difference in the 4.5" & 6" pto drives

    I'm not sure what snowthrower I have.It doesn't have any #'s on it or a a tag and can say from using it at the end of last year that it definetly doesn't throw snow like has been desrcibed on here by some of you .I also know that in th early 90's MTD went a 6" pto drive.I'm also looking at...
  9. J

    M 18 blow by?

    I rerung my engine.It had both blow head gaskets and had blow by before this.The crankcase vent was bad so I replaced w/the updated version.I checked the ring end gap before asy.and was in the middle of spec.I did notice that the valve guide were leaking oil by even w/the stem seals.I didn't...
  10. J

    1811 Hydro Problems...

    On my 1882 I filled the transmission to the full mark and then removed the tube,measured the depth of the fuild and then put a plug in the hole.I use a funnel w/a long reach and put it in the hole that they had the tube sticking thru
  11. J

    1882 reverse soft?

    I removed the the check valves as the one close to the cam plate was leaking.I swapped it out for 1 out of the pump unit I removed.It doesn't seem to be leaking,but I haven't try using it either.I stall tested it.Thanks for the link to danfoss has alittle more description that the cub cadet...
  12. J

    1882 reverse soft?

    My 1882 reverse feels soft like the pressure is low.I went thru the instruction in the service manual as far as the linkage adjustment goes and have that right on the money. I don't find anyone who has messed w/the hydro units.I have replaced the old hydro unit w/this one(thats how I got into...
  13. J

    Front axle spindle bushing for an 1882

    I've looked thru the forum and don't see any info on these.And of course they are discontinued I didn't know if anybody has ever come up w/something that will work or not.
Back
Top