• This community needs YOUR help today. With the ever increasing fees of everything (server, software, domain, e-mail) , we need help. We need more Supporting Members, today. Please invest back into this community to help spread our love and knowledge of IH Cub Cadets. You get a lot of great new account perks including access to private forums. If you sign up for annual, I will ship a few IH Cub Cadet Forum decals too in addition to all the account perks you get. You can see what it looks like below.

    Sign up here: https://www.ihcubcadet.com/account/upgrades

Recent content by rabrown

kirk engines
cc specialties
cub cadet used parts
Advertise with us
IH Cub Cadet Tractor Forum

Help Support IH Cub Cadet Tractor Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. R

    1811 Wiring Schematic

    model - 146782100 serial - 2050601U 753472
  2. R

    1811 Wiring Schematic

    I'm looking for a complete wiring diagram for an 1811 Cub Cadet; specifically for the charging circuit. Is there one available?
  3. R

    Adjusting hydrostat lever to correct neutral position on a Cub 149

    Thanks for your help, Digger
  4. R

    Adjusting hydrostat lever to correct neutral position on a Cub 149

    After replacing the cam and dampener springs on a cub 149, the hydro control lever is not in the neutral position. It is located in the forward position about a 4th of the way up from the neutral position. How can i adjust this so the lever is in the correct position? Also have the same problem...
  5. R

    1811 hydrostat adjustment

    How do you adjust the hydro stat lever to true neutral after replacing the cam and springs that should fix hydro creep?
  6. R

    Tail Lights or Lens

    Looking for tail light lens or complete assembly for Cub 149. Part number for complete assembly is IH-545616-R1
  7. R

    Trading Post

    Looking for decals and foot pads for an 1811 cub that I repainted.
  8. R

    Archive through March 30, 2016

    Thanks, Jim. I will test it out using your suggestions and let you know how it turns out. RAB
  9. R

    Archive through March 27, 2016

    On a Cub 149, I accidentally crossed the dark blue accessory wire to ground. Big Spark! Now my ammeter gauge is registering + voltage even with battery disconnected. Engine starts and runs and ammeter shows a higher than normal charge. When I disconnect the FLD. term from reg. it shows a normal...
  10. R

    Archive through October 13, 2015

    Wayne S. and Jeff B, I got the drive shaft out of my 149 and did not have to move the engine. The drive hub at the engine is wallowd out so took it to have it beefed up by a better welder than I am. Also, did you say I should freeze the new pin and heat the shaft up when installing the new pin...
  11. R

    Archive through October 09, 2015

    My sincere apologies to Jeff for mis-typing his name. I really do appreciate Jeff and Wayne's help with this drive shaft problem. I have not removed the shaft yet but plan to do so today after I smoke up some chicken Hope the rain stays away today.
  12. R

    Archive through October 07, 2015

    Thanks Jake. After further checking you were right. It was the drive pin. I'll get a couple ordered pronto. Thanks again!
  13. R

    Archive through October 07, 2015

    I have a 149 Cub and having a problem with the hydrostat. For a S/n 2050047U tractor, was the hydro made by IH or another manufacturer? if different than IH, who would have made it? Put this thing in gear and nothing happens!Has fluid and engine is running great. was working fine pulling a light...
  14. R

    Archive through August 15, 2014

    Is there such a thing as either a pull behind or 3-point hitch slicer/seeder that can be used on a 149 or larger cub cadet?
  15. R

    Archive through October 10, 2006

    Is there an auxilary hydraulic pump/system that can be added to a 149? Since I didn't get too many ideas on a steel fence post remover, maybe I'll try my hand at building one using hydraulics.
See more
Back
Top