-
This community needs YOUR help today. With the ever increasing fees of everything (server, software, domain, e-mail) , we need help. We need more Supporting Members, today. Please invest back into this community to help spread our love and knowledge of IH Cub Cadets. You get a lot of great new account perks including access to private forums. If you sign up for annual, I will ship a few IH Cub Cadet Forum decals too in addition to all the account perks you get. You can see what it looks like below.
Sign up here: https://www.ihcubcadet.com/account/upgrades
Recent content by pfitzwater
Help Support IH Cub Cadet Tractor Forum:
-
P
Husqvarna - kohler command carb issue "I think
Hey everybody. My father gave me a Husqvarna with a Kohler command 13 engine. last spring it started up ok on the choke but had to everytime. "cold blooded". Went to start it over the winter once and drove it down the drive but then died. pushed it back in the garage and it sat till spring...- pfitzwater
- Thread
- Replies: 0
- Forum: Other Tractors & Large IH Tractors
-
P
Archive through July 14, 2013
I forgot to mention it has a new main belt going from pto to deck but i havent relpace the deck belt. The sub frame probably is a problem. I never thought it locked in properly, (not sure if it does, never seen a good picture of it close up) the quick release lever - Should those tabs be fully...- pfitzwater
- Post #43
- Forum: IH Cub Cadet Tractor Forum
-
P
Archive through July 14, 2013
What would cause The belt from the mule drive keep popping off? Started after I replaced the tension bracket on the mower deck. I adjust the front pulleys to the right position. I wounder if the pulleys on the deck could be worn out or something? Fixing one worn out part reveals more worn out...- pfitzwater
- Post #40
- Forum: IH Cub Cadet Tractor Forum
-
P
Archive through June 10, 2013
have an other photo, showing the clearance of the pulley to the deck.... not a whole lot. First time I had the nut on the bottom and it wasn't giving enough clearance to let the bracket move. flipped it but its still sitting low.- pfitzwater
- Post #3
- Forum: IH Cub Cadet Tractor Forum
-
P
Archive through June 10, 2013
just bought a new mower deck tension bracket from CCS. should the spacer that goes inside the spring be a good 1/4 or so shorter then the spring?- pfitzwater
- Post #2
- Forum: IH Cub Cadet Tractor Forum
-
P
Archive through June 02, 2013
Well turns out that pin was so rusted it must of broke some time ago. Something is still not right thou the clutch is still always engaged. Should the clutch disc be able to move when tightened properly? There is a little slop with the linkage. I'll check out page 15- pfitzwater
- Post #29
- Forum: IH Cub Cadet Tractor Forum
-
P
Archive through June 02, 2013
forgot to post the picture of what im talking about- pfitzwater
- Post #23
- Forum: IH Cub Cadet Tractor Forum
-
P
Archive through June 02, 2013
I know I have talked about this before. I can't get my pto to NOT engage. I may have put it together to tight, I don't have the gauge that came with the rebuild kit any longer. I remember someone saying that with both nuts tightened there should be about 3/8 of the screw showing? I may be wrong...- pfitzwater
- Post #22
- Forum: IH Cub Cadet Tractor Forum
-
P
Archive through June 02, 2013
ok, so a little confused on adjusting the brakes. The pinned end they refer to is the end at the brake pads correct? disconnect the left rod and spin the right wheel. Do I adjust the left side? The side I disconnected? Should the peddle be in the full released position? I have the brakes...- pfitzwater
- Post #6
- Forum: IH Cub Cadet Tractor Forum
-
P
Archive through May 29, 2013
So these are the brakes I have these are the ones with out springs correct? I really shave off the new brake pad? just seems crazy. wouldn't of thought I would have to do that to something new lol I did end up retraceing the threads for the linkage the ends were bent and all. I thought maybe...- pfitzwater
- Post #48
- Forum: IH Cub Cadet Tractor Forum
-
P
Archive through May 29, 2013
How do get new brakes on a 128? I got replacement pads and glued them to the plate. Ones I get one pad on the other pad is so tight I don't think something is right. I have the style that has the housing over the straight brake pads. I know there are three types. I'll try and find the diagram...- pfitzwater
- Post #46
- Forum: IH Cub Cadet Tractor Forum
-
P
Archive through May 29, 2013
well after looking again on CCS I seen that he had one. I bought it. just wish I could get it sooner. The wife is already looking for a landscape company to come out Don't tell the wife I spent more money one the tractor haha- pfitzwater
- Post #16
- Forum: IH Cub Cadet Tractor Forum
-
P
Archive through May 29, 2013
OK, sorry for waiting so long. here is what I have bought. Will the gap between the tube and bolt be acceptable? I could talk to CC maybe if they are willing to talk Looking at this pic, It didn't seem like that much of a gap when I first checked it. of course it will be centered.- pfitzwater
- Post #6
- Forum: IH Cub Cadet Tractor Forum
-
P
Archive through May 26, 2013
Isn't that the truth Charlie @ Jeramia, are you saying the round tube is flat on one side on the inside of the tube? I may have misunderstood that part. I'll show some pictures of what I intend to do tomorrow if the spring will slide on the pipe i bought. bought it this morning and went to...- pfitzwater
- Post #45
- Forum: IH Cub Cadet Tractor Forum
-
P
Archive through May 26, 2013
Hey every one, Got the 128 out and started replaceing the parts that broke last fall. I orderd a new idler tension spring for my 48" deck. went to remove the bolt and it snaped off. Went to a dealer and they said my bracket is broken. The spacer should be attached to the arm and its not. They...- pfitzwater
- Post #36
- Forum: IH Cub Cadet Tractor Forum