• This community needs YOUR help today. With the ever increasing fees of everything (server, software, domain, e-mail) , we need help. We need more Supporting Members, today. Please invest back into this community to help spread our love and knowledge of IH Cub Cadets. You get a lot of great new account perks including access to private forums. If you sign up for annual, I will ship a few IH Cub Cadet Forum decals too in addition to all the account perks you get. You can see what it looks like below.

    Sign up here: https://www.ihcubcadet.com/account/upgrades

Search results

shop deals on amazon
xtreme motor works
Shop deals on ebay
cc specialties
IH Cub Cadet Tractor Forum

Help Support IH Cub Cadet Tractor Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. M

    Archive through January 18, 2014

    Thank you Donald. I appreciate the advice.
  2. M

    Archive through January 18, 2014

    Hello, A roll pin has been sheared on the pump end of my 123; however, the holes around the drive shaft don't line up with the sheared pin. I figure that I could just slide the engine forward so they line up before punching them out. I guess I would need to use some force so the engine bolts...
  3. M

    Archive through January 01, 2014

    Hello all, I was clearing snow off the driveway this morning with my 123, and it was performing well as normal. When I was done I drove it down a the street to clear my neighbors driveway. At first it was performing well, but after I stopped the tractor and pushed the hydro lever forward, the...
  4. M

    Archive through December 14, 2013

    Thanks Frank, I personally get a huge smile when I back up before going full throttle into a snow bank, pushing through the snow like it's the Batmobile driving through a concrete wall.
  5. M

    Archive through December 14, 2013

    Hello, some pictures of this mornings snow that I thought some might enjoy. It was the first time I really got to use the plow, and it's good fun although I found once the heavier snow gets to about a foot, it can be a little tricky.
  6. M

    Archive through May 02, 2013

    It's a 42 inch from blade to blade-3 spindle-for my 67 123- there is up and down movement on the middle/ big spindle-sorry I don't know what part is bad-I want to know if I kneed to spend 300 some odd number of dollars to fix- will it run with slight movement- can't upload pics yet- sorry if...
  7. M

    Archive through May 02, 2013

    Hello all, I am doing a little mower deck overhaul on my 42 inch deck (I believe it is 42). The main spindle seems to not be 100% tight with some up/down movement. I know they are not supposed to move a lot, but it crucial that I fix it now? If there is a part that is bad, what part? I have seen...
  8. M

    Archive through April 20, 2013

    Kraig, will I be able to find a replacement for the bad rag joint near the flywheel? If not, how to I install the correct connection? Is my set-up hurting something?
  9. M

    Archive through April 17, 2013

    Thanks Tom, but what about the rag joint near the hydro filter (first pic)? Will there be a little bit of slack for me to slide it through once I slide the collar back?
  10. M

    Archive through April 17, 2013

    Hello all, I have a 123 and i am trying to remove, and replace the two rubber couplings on the drive shaft. The drive shaft was wobbling, and the rag joints were worn. Do I need to remove the drive shaft completely to get them out? If so, How to I remove it properly? The couplings near the...
  11. M

    Archive through April 13, 2013

    kraig, The engine has not been removed for as long as I have owned it (almost one year). As far as I know the engine is down tight. I will try to fix the rag joint before cutting season. thanks
  12. M

    Archive through April 13, 2013

    Hello all, I have a model 123, and I noticed some slight movement from the driveshaft when I was cranking the engine. The driveshaft appears to be not perfectly aligned. I can't remember if there was a slightly different noise from before. Earlier I realized the rag joint was rubbing against...
  13. M

    Archive through April 07, 2013

    appreciate the help. I took a look under the cub, and I found that the coupling disk was rubbing against the oil filter.
  14. M

    Archive through April 05, 2013

    thanks I will have to take a look under it. I am only a teenager, and a novice when it comes to these cub cadets, so I appreciate the advise. Is the rag joint the circular rubber disk? What will the torn rag joint look like?
  15. M

    Archive through April 05, 2013

    Reggie thanks I will have to take a look under it. I am only a teenager, and a novice when it comes to these cub cadets, so I appreciate the advise. Is the rag joint the circular rubber disk? What will the torn rag joint look like?
  16. M

    Archive through April 05, 2013

    Hello, I have a question regarding to what I believe is the drive shaft making noise during some startups of my 123. The noise appears to be coming from the drive shaft right under my seat. When the engine is warm (after i had already ran it) it makes a sort of rubbing noise, or maybe a bad...
  17. M

    QA 36A snowthrower modifications?

    I recently purchased a QA 36A snow thrower attachment for my narrow frame model 123. It is supposed to fit both narrow and wide frames. Once I brought it home I realized that it did not fit my tractor. There is a peg on the snow thrower bracket where there should be a hole to fit mine. I did a...
Back
Top