• This community needs YOUR help today. With the ever increasing fees of everything (server, software, domain, e-mail) , we need help. We need more Supporting Members, today. Please invest back into this community to help spread our love and knowledge of IH Cub Cadets. You get a lot of great new account perks including access to private forums. If you sign up for annual, I will ship a few IH Cub Cadet Forum decals too in addition to all the account perks you get. You can see what it looks like below.

    Sign up here: https://www.ihcubcadet.com/account/upgrades

Recent content by mpramas

cub cadet used parts
xtreme motor works
shop deals on amazon
kirk engines
IH Cub Cadet Tractor Forum

Help Support IH Cub Cadet Tractor Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. M

    Archive through January 18, 2014

    Thank you Donald. I appreciate the advice.
  2. M

    Archive through January 18, 2014

    Hello, A roll pin has been sheared on the pump end of my 123; however, the holes around the drive shaft don't line up with the sheared pin. I figure that I could just slide the engine forward so they line up before punching them out. I guess I would need to use some force so the engine bolts...
  3. M

    Archive through January 01, 2014

    Hello all, I was clearing snow off the driveway this morning with my 123, and it was performing well as normal. When I was done I drove it down a the street to clear my neighbors driveway. At first it was performing well, but after I stopped the tractor and pushed the hydro lever forward, the...
  4. M

    Archive through December 14, 2013

    Thanks Frank, I personally get a huge smile when I back up before going full throttle into a snow bank, pushing through the snow like it's the Batmobile driving through a concrete wall.
  5. M

    Archive through December 14, 2013

    Hello, some pictures of this mornings snow that I thought some might enjoy. It was the first time I really got to use the plow, and it's good fun although I found once the heavier snow gets to about a foot, it can be a little tricky.
  6. M

    Archive through May 02, 2013

    It's a 42 inch from blade to blade-3 spindle-for my 67 123- there is up and down movement on the middle/ big spindle-sorry I don't know what part is bad-I want to know if I kneed to spend 300 some odd number of dollars to fix- will it run with slight movement- can't upload pics yet- sorry if...
  7. M

    Archive through May 02, 2013

    Hello all, I am doing a little mower deck overhaul on my 42 inch deck (I believe it is 42). The main spindle seems to not be 100% tight with some up/down movement. I know they are not supposed to move a lot, but it crucial that I fix it now? If there is a part that is bad, what part? I have seen...
  8. M

    Archive through April 20, 2013

    Kraig, will I be able to find a replacement for the bad rag joint near the flywheel? If not, how to I install the correct connection? Is my set-up hurting something?
  9. M

    Archive through April 17, 2013

    Thanks Tom, but what about the rag joint near the hydro filter (first pic)? Will there be a little bit of slack for me to slide it through once I slide the collar back?
  10. M

    Archive through April 17, 2013

    Hello all, I have a 123 and i am trying to remove, and replace the two rubber couplings on the drive shaft. The drive shaft was wobbling, and the rag joints were worn. Do I need to remove the drive shaft completely to get them out? If so, How to I remove it properly? The couplings near the...
  11. M

    Archive through April 13, 2013

    kraig, The engine has not been removed for as long as I have owned it (almost one year). As far as I know the engine is down tight. I will try to fix the rag joint before cutting season. thanks
  12. M

    Archive through April 13, 2013

    Hello all, I have a model 123, and I noticed some slight movement from the driveshaft when I was cranking the engine. The driveshaft appears to be not perfectly aligned. I can't remember if there was a slightly different noise from before. Earlier I realized the rag joint was rubbing against...
  13. M

    Archive through April 07, 2013

    appreciate the help. I took a look under the cub, and I found that the coupling disk was rubbing against the oil filter.
  14. M

    Archive through April 05, 2013

    thanks I will have to take a look under it. I am only a teenager, and a novice when it comes to these cub cadets, so I appreciate the advise. Is the rag joint the circular rubber disk? What will the torn rag joint look like?
  15. M

    Archive through April 05, 2013

    Reggie thanks I will have to take a look under it. I am only a teenager, and a novice when it comes to these cub cadets, so I appreciate the advise. Is the rag joint the circular rubber disk? What will the torn rag joint look like?
See more
Back
Top