• This community needs YOUR help today. With the ever increasing fees of everything (server, software, domain, e-mail) , we need help. We need more Supporting Members, today. Please invest back into this community to help spread our love and knowledge of IH Cub Cadets. You get a lot of great new account perks including access to private forums. If you sign up for annual, I will ship a few IH Cub Cadet Forum decals too in addition to all the account perks you get. You can see what it looks like below.

    Sign up here: https://www.ihcubcadet.com/account/upgrades

Recent content by dslater

xtreme motor works
cadet connection
kirk engines
Advertise with us
IH Cub Cadet Tractor Forum

Help Support IH Cub Cadet Tractor Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. D

    16 HP wants to vibrate

    I have known some guys that have them and they run them wide open all the time, any slower they shake bad. David
  2. D

    Archive through February 17, 2009

    Are the spindle bearings for the older decks as on a 122 or a 1450 still available? I have several in need. David
  3. D

    Archive through January 13, 2009

    Looking at the FAQ's I see that the manual transmissions are to have Hy-tran is this correct? Thanks, David
  4. D

    Archive through November 29, 2008

    Anyone know why some hydros are noisier than others? New hy-trans and filter in each. Thanks for any information, David
  5. D

    Archive through November 02, 2008

    Thanks for all the help on the QA 42 blower. I didn't know what model till I looked on the parts lookup. It is a QA42 not an "A". The sprocket is not replaceable so it is going to the machine shop to turn off the old one. I'll have them leave a shoulder for the new one and weld it on. I want...
  6. D

    Archive through November 02, 2008

    Is the chain sprocket on the snowblower auger replaceable? I have one with the teeth worn near gone. Thanks guys, David
  7. D

    Archive through August 14, 2008

    Paul E. Funk, It was the roll pin that had broken. Slipped in a new one and I'm good to go. Thanks for the information. David
  8. D

    Archive through August 14, 2008

    I have a creeper gear that isn't working. I took it off and the lever that shifts it has become disconnected. Problem is I don't know how it is supposed to link to the sliding gear. The shaft turns but not the fork that moves the gear. Any thoughts? Thanks, David
  9. D

    Archive through January 09, 2008

    Carey, Last year I had the same thing happen to me with the carb. I did everything by the book, new needle and seat, gaskets and set everything like it should be. It still leaked. I decided that day was going to be spent figuring it out, start from scratch again. I put some gas in a coffee...
  10. D

    Archive through December 05, 2007

    Matt, I'm leaning that way, if I order tonight I can get them by Monday. Thanks, David
  11. D

    Archive through December 05, 2007

    Guys, If you had a choice what tire size would you use for snow plowing with a blade? I have 8.5, and 10.5's and want to order chains for one of them. This is for my 1450 or the 782, I'm wanting to use the hydraulic lift. David
  12. D

    Archive through December 05, 2007

    DonT, I just did my 105 this way. I bushed #1 and 7 with bronze bushings. My pins were not worn at all for some reason. I couldn't find any steel bushings. #1 & 7 parts are very hard, need to be annealed before any reaming or drilling will go on. On part #6 the center of the slot (neutral...
  13. D

    Archive through December 02, 2007

    Earl LaMott, I read your post a couple pages back and was wondering if you got the spring replaced. I'm not sure it is possible through the cover. Why was it coming off? Are the ends bent? What type of noise was it making, I have a noise in my K241 that bugs me. Thanks, David
  14. D

    Archive through November 26, 2007

    Dudley, One the slop between 1 & 6 on the diagram. What I've done is weld up the pin and form to size. Then I measure the ends of the slot to get the narrowest size, then I put the plate in my large vice and squeeze (the center of slot) down to that size in the center, where the slop is. I've...
  15. D

    Archive through November 19, 2007

    Evening guys, I have my 105 transmission out and need to tighten up the linkage. I'm doing that OK but I'm wondering how I will set the neutral with most everything under the tunnel cover. I have everything off that will come off but it's still tight in there. I've looked at the FAQ's but...
See more
Back
Top