• This community needs YOUR help today. With the ever increasing fees of everything (server, software, domain, e-mail) , we need help. We need more Supporting Members, today. Please invest back into this community to help spread our love and knowledge of IH Cub Cadets. You get a lot of great new account perks including access to private forums. If you sign up for annual, I will ship a few IH Cub Cadet Forum decals too in addition to all the account perks you get. You can see what it looks like below.

    Sign up here: https://www.ihcubcadet.com/account/upgrades

Search results

kirk engines
shop deals on amazon
cc specialties
Advertise with us
IH Cub Cadet Tractor Forum

Help Support IH Cub Cadet Tractor Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. M

    127New Belt too short.

    Thank you all
  2. M

    Aftermarket Mufflers?

    No, but I think the mufflers are the same.
  3. M

    Aftermarket Mufflers?

    well, it came with a 10 horse
  4. M

    Aftermarket Mufflers?

    I need a new muffler for my Narrow Body 10 hp 127. Anyone ever buy and had good luck with an aftermarket unit?. OEM are way too pricey. MTD Cub Cadet IH-393840-R91 MUFFLER
  5. M

    127New Belt too short.

  6. M

    127New Belt too short.

    Yes, I went to a dealer and got the right belt. I do run it high rpm, but I was checking it out before reving it up. The pulleys are set pretty much even and they are spinning well. deck pulleys seem ok. I checked all that beforehand. Ifeel a bit stupid knowing so little, but all I have ever...
  7. M

    127New Belt too short.

    Ok, I got the right belt 80" Thank you so much for the help. I have had this 127 since 1976 from a neighbor. I put the new belt on however, now the whole belt system is shaking and the tension pulley on the deck is doing a lot of back and forth. I gave it more RPM and it seems fine now, but...
  8. M

    127New Belt too short.

    I measured the back of the deck so that is wrong
  9. M

    127New Belt too short.

    My mule drive belt failed and I ordered the correct replacement IH 489397-R3. (77") This new belt is too short. I only winds around to the grease zerk in the center pulley. No way can I stretch it far enough to go around the pulley. Is there a longer belt. It the original deck 48" on a 127...
  10. M

    New Blades for a 127? Need Recommendation.

    Thanks fellas
  11. M

    New Blades for a 127? Need Recommendation.

    I have been disappointed for years on how quickly blades dull. Do any of you folks have a particular favorite. And, by the way do I turn the blade bolt counterclockwise to remove it. Thanks Mike
  12. M

    Archive through January 28, 2015

    I have two older units. A 127 narrow and a 128 wide with a rebuild motor. I was wondering if any of you all use Mobil I in your motors and what weight?
  13. M

    Archive through January 26, 2015

    I have two older units. A 127 narrow and a 128 wide with a rebuild motor. I was wondering if any of you all use Mobil I in your motors and what weight?
  14. M

    Archive through May 24, 2014

    To Paul Bell: That 108 is worth a lot more than 350.00. Maybe give it some time. That is very nice looking tractor with the right deck and just enough HP to do almost anything. I have one also with a creeper. Amazing tractors.
  15. M

    Archive through May 09, 2014

    Dennis: I have had the Fumoto on my 127 for 3 years. I love it and there is plenty of room. It is pretty bullet proof device.
  16. M

    Archive through May 09, 2014

    Thanks Bill. Mike
  17. M

    Archive through May 09, 2014

    I have a wide body 12hp 108. I want to buy a Fumoto valve to replace the oil pan drain plug. Can someone tell me the thread size of the plug or the bolt size if that is more appropriate. Here is a link to their size chart. I have one with a nipple to add a hose and it make changing the oil a...
  18. M

    Archive through September 04, 2011

    Narrow frame mule drive with pullys. My spring side pulley bracket has worn itself a pretty large hole over the cross shaft causing the spring side pully to twist enough that the belt no longer drops straight into the pully. Anyone have a complete unit that is free of wear? The shaft is welded...
  19. M

    Archive through August 14, 2011

    After getting some good advice on how to lower the front end of my deck by bending the pickle bar I removed the deck in preperation for that chore.. Then I remembered that somewhere in the shed, from an old yard sale, I had a set of Quietline deck pins that I knew were 1" higher that the those...
  20. M

    Archive through August 14, 2011

    Dennis: Thanks for your input. This is a new tractor to me but I have owned a 127 for 36 years. My current shaft is good and round. The lever or pikle bar sissors end only goes over the shaft about half way, which I am told is as it should be. But the front of the deck is a good inch lower...
Back
Top