• This community needs YOUR help today. With the ever increasing fees of everything (server, software, domain, e-mail) , we need help. We need more Supporting Members, today. Please invest back into this community to help spread our love and knowledge of IH Cub Cadets. You get a lot of great new account perks including access to private forums. If you sign up for annual, I will ship a few IH Cub Cadet Forum decals too in addition to all the account perks you get. You can see what it looks like below.

    Sign up here: https://www.ihcubcadet.com/account/upgrades

Recent content by shoff

Shop deals on ebay
kirk engines
cadet connection
Advertise with us
IH Cub Cadet Tractor Forum

Help Support IH Cub Cadet Tractor Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. S

    Archive through May 25, 2009

    Thank you, David C. I just saw your reply to my question.
  2. S

    Archive through May 25, 2009

    Thanks Frank!
  3. S

    Archive through May 24, 2009

    Frank, thanks for the picture. It looks to me like you must have to drill the hole out larger in the lever shaft. Do you by any chance know what size bolt that is that goes through the shaft?
  4. S

    Archive through May 22, 2009

    Hello everyone. Long time, no post. I have a question about my hydraulic lift lever on a 1450. I've searched the FAQs and done a few searches on the site, but haven't found anything. The roll pin broke in my hydraulic lift handle yesterday. I replaced this several years ago and I recall that...
  5. S

    1641 Cub Cadet info

    Michael, did you like the 1641?
  6. S

    1641 Cub Cadet info

    Thanks Michael. I wondered if maybe something could be done there since that is where the lift rod attaches on my 1450. Does anyone know if the attachments will interchange with a wide frame Cub Cadet such as a 1450? I know the belt width is different for things such as a blower, but am not sure...
  7. S

    1641 Cub Cadet info

    Hi All. I just inherited a 1641 Cub Cadet from my late grandfather. I know virtually nothing about this machine, have no manuals yet, etc. I was wondering how any front mount implements lift because I see no provisions for a lift rod attachment. Also, was a Cat-0 3-point hitch available for this...
  8. S

    Archive through August 27, 2004

    Good morning everyone! Could anyone tell me if the pto clutch from a 682 will fit a 1450? I know they have different engines, but thought maybe the pto clutch might be the same.
  9. S

    Archive through August 27, 2004

    Hello everybody. The positive (+) wire has come out of the PTO clutch coil on my 1450. The end of the wire is recessed into the coil housing, so I have no way to solder onto the existing wire like I had hoped to do when I took the PTO clutch off to repair the broken wire. I was curious if anyone...
  10. S

    Archive through June 14, 2004

    Re: My 1450 problems:I'll try the old condensor and test the new one to make sure it's good. I'll also get a new spark plug in the morning to be safe. Thanks for all the suggestions. By the way I did check to make sure there isn't a blockage in the fuel supply. I took the line loose at the...
  11. S

    Archive through June 11, 2004

    Ken- I tried it with a little choke, a lot of choke, no choke... couldn't get it to do anything. I'll check the condensor out and see if it is ok. Thanks.
  12. S

    Archive through June 11, 2004

    I'm having some trouble with my 1450 CC. I was having trouble with it bogging down under load a couple weeks ago. I changed the points and condensor and it seemed to run pretty well for a couple weeks after that. The last time I mowed with it, I had been mowing for about 30 minutes, shut it down...
  13. S

    Archive through May 11, 2004

    Kraig, Thank you very much!!
  14. S

    Archive through May 11, 2004

    Help! My 1450 is is in dire need of a tuneup. I think the points are on their way out. I don't have a shop manual for this tractor and I really need to get it going before I can have one here in the mail. Could anyone tell me the procedure for installing and adjusting the points on this 14...
  15. S

    Archive through April 01, 2004

    Hi Guys! Thanks for the help Dave and Digger. I do have one more question though. Does the tiller use the same mule drive as the mower deck? Thanks again. Shawn
See more
Back
Top