• This community needs YOUR help today. With the ever increasing fees of everything (server, software, domain, e-mail) , we need help. We need more Supporting Members, today. Please invest back into this community to help spread our love and knowledge of IH Cub Cadets. You get a lot of great new account perks including access to private forums. If you sign up for annual, I will ship a few IH Cub Cadet Forum decals too in addition to all the account perks you get. You can see what it looks like below.

    Sign up here: https://www.ihcubcadet.com/account/upgrades

Recent content by Mike Hoover

Shop deals on ebay
cc specialties
shop deals on amazon
kirk engines
IH Cub Cadet Tractor Forum

Help Support IH Cub Cadet Tractor Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. Mike Hoover

    Member Introduction

    Well, Cubbies Well, Cubbies, I am not new to the site but it has been a while. I think I screwed up. A year ago or so, I was rebuilding a 106 after something snapped in the drivetrain and believing that it was the clutch went out. I bought all the parts needed and found that the linkage to the...
  2. Mike Hoover

    Tractor For Sale 106 cub for sale. Whole or parts

    Items are sold
  3. Mike Hoover

    Tractor For Sale 106 cub for sale. Whole or parts

    I have a 106 Cub for whole or parted out. I have two other cubs and need some garage space The following are a list of pcs indivdualually 42in snow plow with mule $100.00 2_50lb wheel weights $100.00 48 in mower that has been refurbished with metal plating $100.00 1-wide frame...
  4. Mike Hoover

    My 106 needs some giddy up and go

    When clutch is pushed in, driveshaft moves to the rear. I understand the driveshaft is not suppose to move. Also, on the outside of the transmission in the rear, you can see the shaft moving. I looked a several diagrams and can't tell if there is a cap or something else to keep the shaft from...
  5. Mike Hoover

    My 106 needs some giddy up and go

    Looking for some who has experience in repairing a clutch/ transmission problem for my 106 10hp garden tractor near Pittsburg, Pa. I have rewired electrical system/had starter generator rebuilt. Starts and runs perfect. I replaced clutch but something is wrong with transmission or linkage. I...
  6. Mike Hoover

    What'll I do now!

    Well gents, I have found everything I did to replace the clutch ok. When I push clutch in the driveshaft moves to the rear. I know the driveshaft is not to move. What I found out was something came loose, a bearing broke, whatever in the transmission. I put a putty knife in back of collar in...
  7. Mike Hoover

    What'll I do now!

    Well, I tell ya that I blew the clutch our and it was cracked. I was pulling a large rock with a chain when it let go. When I started tearing down, notice wiring was shot with the paper insulation. Replaced all that and it runs fine. Pounded out pins, replaced with new clutch and installed pin...
  8. Mike Hoover

    What'll I do now!

    I am at a crossroads with my restoration of my 106 Cub. I replaced the clutch with the springs. When I started engine and pushed clutch in, the driveshaft moved backwards and springs came off or bent. Should the driveshaft move? I was told by someone familiar with cubs that there maybe something...
  9. Mike Hoover

    Need some advice

    I rebuilt my 106 electrical system, new wires, starter rebuilt and replaced clutch. Runs great, but the cannot shift without stopping engine. I am not sure whether the rear pin goes before or after the clutch release lever.The teaser spring looks ok The clutch cracked after 50 years I put the...
  10. Mike Hoover

    My little 106 headache

    No one else having this problem
  11. Mike Hoover

    My little 106 headache

    Well, an update on rebuilding my 106. Replace the clutch and rewired everything new. Hit the choke alittle and it fired right up. Beautiful music. Only problem, the clutch springs that hole the clutch in place hit the bottom nut of the bottom spring. On further observation, I find the the...
  12. Mike Hoover

    Faithful 106

    Got a sister to yours! Been in family since new, but has seen better days. I too am rebuilding wiring harness. Guess they never expected to last 52 years. LOL.
  13. Mike Hoover

    Help, I've fallen and can't get it right

    I isolated the rebuilt starter generator and found that I put an ohm meter from ground to the two top terminals I get a short. The guy said his polished the armature and put new brushes in it and put it on the new regulator and found it was charging. What could be causing a short?
  14. Mike Hoover

    Help, I've fallen and can't get it right

  15. Mike Hoover

    Help, I've fallen and can't get it right

    You maybe right.
See more
Back
Top