Brad Kamm

Well-known member From Abrams, WI

Joined: Sep 21, 2020

Last seen: Sunday at 10:15 AM

Latest activity Postings About

- Brad Kamm replied to the thread Cub Original mower spindles.
  
  To be honest, if I planned to make this my regular mower, I would need to replace all the bearings and spindles and belts. That’s $300 I...
  
  Nov 17, 2022
- Brad Kamm reacted to John Wyrick's post in the thread Rear Engine Riders with Like.
  
  OK- the 85 Special works hard mowing and picking up Ozark oak leaves. The 60 gets started and driven up and down the road and makes me...
  
  Nov 17, 2022
- Brad Kamm replied to the thread Cub Original mower spindles.
  
  I’m not pulling because of how they look, doing it so I know they are lubed . These could be 40-50yo, they don’t sound dry, but they are...
  
  Nov 16, 2022
- Brad Kamm reacted to danderson's post in the thread Cub Original mower spindles with Like.
  
  That’s typical. John Deere is the same way. They put a grease fitting on the housing but sealed bearing. Yes, just pull the inner seals.
  
  Nov 16, 2022
- Brad Kamm reacted to lpalma's post in the thread Cub Original mower spindles with Like.
  
  I did one in the spring and it had the same beaings as yours, There was no zerk on the shaft, more than likely it was original as the...
  
  Nov 16, 2022
- Brad Kamm replied to the thread Cub Original mower spindles.
  
  The bearings feel ok, I think I’ll pull 1 seal, face those sides together and reinstall. Flush and repack bearings as well. I don’t plan...
  
  Nov 16, 2022
- Brad Kamm posted the thread Cub Original mower spindles in IH Cub Cadet Tractor Forum.
  
  While tearing down the deck spindles, I found that the 2 bearings have seals on both sides. I don’t understand how grease is getting...
  
  Nov 15, 2022
- Brad Kamm replied to the thread Need Cub Original Photos.
  
  Where did you get yours from?
  
  Nov 6, 2022
- Brad Kamm reacted to kmcconaughey's post in the thread Need Cub Original Photos with Like.
  
  Nov 4, 2022
- Brad Kamm replied to the thread Need Cub Original Photos.
  
  Just as you suspected, it was bent slightly, tweaked it down a little and it fits nice. I’m down to choke cable, driveshaft, and a...
  
  Nov 3, 2022
- Brad Kamm replied to the thread Need Cub Original Photos.
  
  Those are good photos, thanks! Couple questions, what color should the dash decal be? Black, white , or silver? I’ve seen all 3 for...
  
  Nov 3, 2022
- Brad Kamm replied to the thread Need Cub Original Photos.
  
  Thanks, my shop doubles as mancave, wood shop, auto shop, and Cub shop. And 1 deer skinned out so far this year! Post those “O” pictures...
  
  Nov 2, 2022
- Brad Kamm posted the thread Need Cub Original Photos in IH Cub Cadet Tractor Forum.
  
  I have been doing a resto on my Original, disassembled, sandblasted, primed, and painting. As I’m reassembling, I’m wondering about...
  
  Nov 2, 2022
- Brad Kamm reacted to CӞ.'s post in the thread Bought something else i prolly dont need. with Like.
  
  i’m glad i ran out of wood to cut 🪵 or else i’d STiHL be out there splitting it! 😆
  
  Oct 18, 2022
- Brad Kamm replied to the thread Bought something else i prolly dont need..
  
  My dad bought a Stihl with that type of recoil. He was 78 at the time and was still using an outdoor wood stove for heating the house...
  
  Oct 18, 2022
Show older items
Loading…
Loading…