• This community needs YOUR help today. With the ever increasing fees of everything (server, software, domain, e-mail) , we need help. We need more Supporting Members, today. Please invest back into this community to help spread our love and knowledge of IH Cub Cadets. You get a lot of great new account perks including access to private forums. If you sign up for annual, I will ship a few IH Cub Cadet Forum decals too in addition to all the account perks you get. You can see what it looks like below.

    Sign up here: https://www.ihcubcadet.com/account/upgrades

Recent content by zsmolka

shop deals on amazon
cc specialties
cub cadet used parts
Shop deals on ebay
IH Cub Cadet Tractor Forum

Help Support IH Cub Cadet Tractor Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. Z

    Archive through November 23, 2008

    Hi Guys, do you guys know if a 129 or 149 hydro/trans will fit the 1400's?
  2. Z

    Archive through March 18, 2008

    Do any of you know what the gear ratio of the 147 differential is? Is it the same as the 123?
  3. Z

    Archive through November 12, 2007

    Will it couse damage to my 147's hydo rearend to drive in water just above the axal??
  4. Z

    Archive through September 20, 2007

    Charlie, Would the 1450 trans bolt up ok the the wide frames ie 149 1200? also is the hydrostat unit alone able to fit into the 147 without problems or is the problem with the diff/trans?
  5. Z

    Archive through September 20, 2007

    Thankyou Charlie!
  6. Z

    Archive through September 20, 2007

    Charlie, what do you mean that's about all? will every thing else be wrong?
  7. Z

    Archive through September 20, 2007

    Does anybody know if the hydro and trans/diff out of a 1450 will fit in a 147 ??
  8. Z

    Archive through September 24, 2007

    Hey Darryl, do the drive shaft directions of the hydros spin in the same directioin(clockwise looking at the diff from the drive shaft input) or did you have change the direction of one of the hydros? Did you need to flip the ring gear in the front diff? Sweet tractor, does it pull well? Are...
  9. Z

    Archive through September 14, 2007

    I wanted to build a four wheel tractor that had one hydro in the back and one in the front that shared the same drive shaft. Oh but the drive shaft of the one in the front would spin the wrong way huh? so I would need to flip the ring gear and change the direction of the drive shaft to the front...
  10. Z

    Archive through September 14, 2007

    Could a guy flip the diff ring in a 1450 hydro rear end to make it go backwards when the lever is in the foreward position?
  11. Z

    Archive through September 14, 2007

    What is the main difference between the 1450 and the 147? Is the hydro and trans as strong and wonderful in the 1450? are parts for it cheaper or easyer to get?
  12. Z

    Archive through May 10, 2007

    Hey guys, I hooked up my 42" tiller today and did a lot o tillin. One thing I noticed was when the tines were really digging deep the clutch on my PTO would slip and I would need to raise the tiller a litte. Is this supposed to happen?
  13. Z

    Archive through March 29, 2007

    Hey guys, I have a new/old tille(A1 A2 A somthing) that has a 90 degree deal that attaches to my hydro diff where the cover bolts on. When people attach these things do they loose all their hy0tran?? Should I just count on replacing the hy-tran or should I capture it and reuse it? Will it be...
  14. Z

    Archive through February 28, 2007

    I have a 147 and bought a Brinly mold plow. I probly need chains since I dont have ag.tires, right? Also do I need to put any other weight on the tractor other than my 30lb tire weights? thanks
  15. Z

    Archive through February 16, 2007

    Mike, Im new to the post too and don't know a whole lot but I do know that if it had a 321 in her befor and you replace her with a nother 321 you should be good to go. The only thing I could think of that might go wrong is that some of the crank shafts are 1" and others are 1 1/8". As far as the...
See more
Back
Top