• This community needs YOUR help today. With the ever increasing fees of everything (server, software, domain, e-mail) , we need help. We need more Supporting Members, today. Please invest back into this community to help spread our love and knowledge of IH Cub Cadets. You get a lot of great new account perks including access to private forums. If you sign up for annual, I will ship a few IH Cub Cadet Forum decals too in addition to all the account perks you get. You can see what it looks like below.

    Sign up here: https://www.ihcubcadet.com/account/upgrades

Recent content by rhribar

kirk engines
shop deals on amazon
cc specialties
Advertise with us
IH Cub Cadet Tractor Forum

Help Support IH Cub Cadet Tractor Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. R

    Archive through September 02, 2010

    I am using it for added weight I just heard about usingtiresealer or foam . It had the added advantage of not getting a flat tire
  2. R

    Archive through September 02, 2010

    I plan on mounting Firestone Floatation tires on my machine. The size will be 23x10.50x12. They will be on 8.5 inch rims. My question is : What is the preferred loading method? Window washer fluid or tire sealer ?
  3. R

    Archive through April 08, 2010

    if I would have asked if anyone had a disconnect, would my thread have been deleted? Would the proper place be the classifieds?
  4. R

    Archive through April 07, 2010

    Kraig they had a couple listed then when i knew what i was looking for, a centrifigal clutch . I went to Ebay and they have new 30 hp clutches from $200 to $400
  5. R

    Archive through April 07, 2010

    I bought a hydro disconnect from a place in South Bend I did check sponsors on top of page. no one had one
  6. R

    Archive through April 06, 2010

    Kraig thank you for reply I placed a bid on an assembly on Ebay I have 2 hydros and 2 hydraulic pumps to turn over when cold. Was looking for inline electric clutch, could not find what I wanted
  7. R

    Archive through April 06, 2010

    could I use the 108 tractor driveshaft/ clutch assembly in place of the drive shaft on a Hydro? The reason I would do this is to take all the load off motor when trying to start motor
  8. R

    Archive through February 21, 2010

    I am looking for a complete coulter setup [email protected]
  9. R

    Archive through March 03, 2010

    Is it possible that I am in the wrong section? I have a limited knowledge of Cub Cadets. It appears that loader was made out of a 1450 and a 1650. Guess I will have to look for ID's
  10. R

    Archive through March 03, 2010

    I have two rear ends on my Ken Birkey loader. One has the ports for the hydro lift which was used for the power steering. The other has the ports plugged. Ihave the proper plugs to plug the ports that were used for the power steering, I checked the charge ports and found that all four looked...
  11. R

    Archive through March 03, 2010

    First question I am starting a new topic, Is this is proper way ? It appears I have a ported transmision, Can I cap off those ports? And it appears that there has been a heated discussion on HyTran. IS this only available at CIH dealer ? There is not a CIH dealer near by. I looked at...
  12. R

    I'm from the other side of the tracks

    That is my tractor(?) loader I joined hopeing to possibly contact him. I'm changeing the source for the power steering and that is why I asked the question on the hydrostatic connections.
  13. R

    I'm from the other side of the tracks

    What is the procedure for putting pictures on site ? On the other side of tracks it is pretty complicated
  14. R

    I'm from the other side of the tracks

    I am addicted to another brand of tractor. (S) But I acquired a 4wd payloader tractor that I think was built by one of this clubs members. Birkey (?). Being new to Cub, I have several questions. 1. The hydrostatic looks very similiar to what I had before. When a hydro lift was put on, the...
See more
Back
Top