• This community needs YOUR help today. With the ever increasing fees of everything (server, software, domain, e-mail) , we need help. We need more Supporting Members, today. Please invest back into this community to help spread our love and knowledge of IH Cub Cadets. You get a lot of great new account perks including access to private forums. If you sign up for annual, I will ship a few IH Cub Cadet Forum decals too in addition to all the account perks you get. You can see what it looks like below.

    Sign up here: https://www.ihcubcadet.com/account/upgrades

Recent content by dhodgson

cub cadet used parts
Shop deals on ebay
cc specialties
cadet connection
IH Cub Cadet Tractor Forum

Help Support IH Cub Cadet Tractor Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. D

    Milling Machines

    anyone have a schematic for a old 3uh summit horz. milling machine ser #3262 Just got this 6750 lbs machine for the effort of picking up. Thanks to the fact I retired from heavy equipment and lotsa old favors owed. Thanks Doug
  2. D

    Archive through June 25, 2012

    Just my word on vanguard B/S motors and motor swaps with direction problems. The B/s motor uses a plain out put case no bearing. Basically a hole drilled through alum. not even a Babbitt insert. this can work on low load oil presurised locations but this is not what you want here if you want...
  3. D

    Craftsman with front end loader

    Ive got a Sears 1976 with front end loader and electric three point lift Onan motor All is good on it except i think I'm missing some parts on the elect lift sears mod 917253130 sears catalog didn't help anyone have a pic of this creature
  4. D

    Archive through December 24, 2008

    What is all that white fluffy stuf in your pic's Doug in Tx
  5. D

    Archive through June 21, 2008

    Looking for a center blade mount with pulley and bearing hub complete for a 149 deck.Thanks Doug!
  6. D

    Archive through June 01, 2008

    need front Axel for wide frame 149 just need Axel got lots trading stuff Doug in TX.
  7. D

    Archive through April 04, 2008

    How dose a little boy get everything he wants for Christmas? He asks daddy for a dolly!
  8. D

    Archive through April 04, 2008

    ultimate put down!! your practicing solo eroticism and your hand goes to sleep
  9. D

    Computer ?

    is there a easy way to reply to a member? all i can figure out is go to profile coppy e mail add. then go to mail
  10. D

    Archive through April 23, 2008

    Starter generators insp. & tested $50. plus shipping
  11. D

    Archive through April 06, 2008

    Tsdeese needed lug nuts I got em but dont know how to reply to him Gust pay shippin & $5. handelin Doug in Tx
  12. D

    Archive through April 06, 2008

    Charley Thanks for info on tires just orderd a badley needed set. All ive got is 50% sand.need tracksion.Doug. in Taxass.
  13. D

    Pipe Bending

    if all you want is hyd. to raise a plow try this. All the time i get power trim pumps off junk boats for free. Mercruiser power trim pump is 12 volt easy to use automaticly holds load up 1 wire to ground one hot for up another one for down. Gust have to watch whitch hose to use for up&down.Up...
  14. D

    Air Compressors

    a good air dryer is a coil of copper tube with drain valve at end of loop inside back wall of your beer fridge cooled down air condensates moisture and your shure to blead it ! hell your going there all the time anyway Doug in Texas
  15. D

    18 hp briggs vangaurd in place of kohler?

    vangaurd dose not use a bearing on output shaft side crank just runs in housing . when it wears you have to replace compleat housing all so cam is hollow on end for compression release mec. $235. for new cam better of with kohler i know a place that ocasonly has new kohlers at a deal if you...
See more
Back
Top