• FIRST AND LAST NAMES ARE REQUIRED WHEN REGISTERING

Look what pulled in my driveway today.\

IH Cub Cadet Tractor Forum

Help Support IH Cub Cadet Tractor Forum:

dschwandt

Well-known member
IHCC Supporter
Joined
Mar 31, 2012
Messages
4,782
displayname
David Schwandt
Did not want to ruffle any feathers seeing as this is not an IH piece so posting this here.
CCC 2086 w/near perfect nose, hood and side panels, 60" Haban, 42" snow blade and new set of 2 link chains.
plastic tunnel cover is cracked and the right side panel has a little piece broken off just below the muffler.
This will make an awesome mowing machine for the cemetery.
 

Attachments

  • DSCN9468.JPG
    DSCN9468.JPG
    3.3 MB · Views: 0
  • DSCN9469.JPG
    DSCN9469.JPG
    3.1 MB · Views: 0
  • DSCN9470.JPG
    DSCN9470.JPG
    3.3 MB · Views: 0

digger

Administrator
Staff member
Administrator
Moderator
IHCC Sponsor
IHCC Supporter
Joined
Jun 22, 2002
Messages
15,972
Location
Park Rapids Mn.
displayname
Digger
Did not want to ruffle any feathers seeing as this is not an IH piece so posting this here.
CCC 2086 w/near perfect nose, hood and side panels, 60" Haban, 42" snow blade and new set of 2 link chains.
plastic tunnel cover is cracked and the right side panel has a little piece broken off just below the muffler.
This will make an awesome mowing machine for the cemetery.
Well done man!!!!! :cubwinker:
 

dschwandt

Well-known member
IHCC Supporter
Joined
Mar 31, 2012
Messages
4,782
displayname
David Schwandt
Copy on that!
No problem as it will be dedicated to the back 40 where there are no burials yet.
Only issue I can see is the deck mounting.
It is a 374 and the 2036 calls for a 325, different rear mount.
I think we can figure out something though.

I think we should haven a sub forum section for Supers only??
 

Bret McFarland

Well-known member
IHCC Supporter
Joined
Jun 30, 2022
Messages
129
Location
Western Maryland
Copy on that!
No problem as it will be dedicated to the back 40 where there are no burials yet.
Only issue I can see is the deck mounting.
It is a 374 and the 2036 calls for a 325, different rear mount.
I think we can figure out something though.

I think we should haven a sub forum section for Supers only??
Yes definately, a Supers forum section would be great.
 

dschwandt

Well-known member
IHCC Supporter
Joined
Mar 31, 2012
Messages
4,782
displayname
David Schwandt
Possibly, Close ups of how it is mounted at the rear of the deck might.
This one looks to have been cobble crafted to fit the 2086 using the 374 style mount back there.
 

jstewart

Well-known member
Joined
Jun 6, 2007
Messages
162
displayname
jon stewart
I don't look down on Cyclops, they were a worthy successor..............................and I will not rest till I find a Super, unfortunately they all seem to be 300+ miles away.
 

dschwandt

Well-known member
IHCC Supporter
Joined
Mar 31, 2012
Messages
4,782
displayname
David Schwandt
HELP!!!

Working on hanging the 374 deck under the 2086 and need to know if I must get the deck drive pulley for a 325 deck as that is the deck spec'ed for the 2086.

The PTO pulley on the 2086 is 6" dia. whereas the PTO pulley on the 374 is made for the smaller engine PTO pulley like the 1872.
 

dschwandt

Well-known member
IHCC Supporter
Joined
Mar 31, 2012
Messages
4,782
displayname
David Schwandt
Got around to working on it this week.
Over-nite parts from McMaster Carr showed up today in the form of new bushings for the steering knuckles.
Got them installed today as well as the new tie rod ends and PS cyl ends received earlier.
Making a new swivel pin for the bell crank that holds the short tie rods in the front of this tractor.
Should steer like a new machine now!
 

Attachments

  • DSCN9771.JPG
    DSCN9771.JPG
    3.3 MB · Views: 0

Oak

Well-known member
Joined
Oct 26, 2019
Messages
118
Location
Georgia
David, do you have a part number on those bushings? I probably need to order some of those for my fleet.

How many hours are on that FD620 Kawi? Was the cam gear changed yet? If not, that would be a nice winter project.
 

dschwandt

Well-known member
IHCC Supporter
Joined
Mar 31, 2012
Messages
4,782
displayname
David Schwandt
Here's the bushing info

��
Delivers Oct 13
1Oil-Embedded Bronze Sleeve Bearing
for 1" Shaft Diameter and 1-1/8" Housing ID, 1-1/2" Long
6391K649
4
each​
7.02
each​
$28.08​
 
Top