• This community needs YOUR help today. With the ever increasing fees of everything (server, software, domain, e-mail) , we need help. We need more Supporting Members, today. Please invest back into this community to help spread our love and knowledge of IH Cub Cadets. You get a lot of great new account perks including access to private forums. If you sign up for annual, I will ship a few IH Cub Cadet Forum decals too in addition to all the account perks you get. You can see what it looks like below.

    Sign up here: https://www.ihcubcadet.com/account/upgrades

Search results

kirk engines
Shop deals on ebay
shop deals on amazon
Advertise with us
IH Cub Cadet Tractor Forum

Help Support IH Cub Cadet Tractor Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. gloughery

    1863 axle splined steering arm

    Took an 1863 axle apart, cleaned it up, and painted it yellow. I don't know the direction to replace the splined steering arm. More questions about replacing the steering column with this in a 122. Sure would appreciate some advice please. Thanks.
  2. gloughery

    Rolling bearings under NF spindle

    Bought a set from McMaster-Carr for my 70 and then realized it may cause the pin hole to not line up at the top. The bearing is .078 and the two washers are .031 each. Will 0.140" raise the spindle too high that the pin won't fit back in place?
  3. gloughery

    1863 axle for NF

    Hello, I am doing the super steer upgrade with an 1863 axle (part 719-3101) on both a narrow 122 and a wide frame 169. I bought two and took them all apart to clean them up. A couple of questions. 1) One has a straight drag link and the other has a bent drag link (next to each other in photos)...
  4. gloughery

    Drive shaft constantly spins CC100

    Need advice why the drive shaft constantly spins. Photo shows pressure plate pulled away for inspection and engine not running. Tried everything in the book and not quite sure what is going on. Clutch adjustments have been made. One suggestion is the shaft isn't straight into the engine and a...
  5. gloughery

    #2 Cart Specs

    Hello, I just bought an Onan 5.0 CCK mounted on an IH #2 cart. Nothing better than that! The problem is the cart tires are dry rotted and I need to take a set of new ones with me. Are these standard axles with a cotter pin or is the axle drilled out like a spindle? I will eventually get IHCC...
  6. gloughery

    Front steering knuckle bolt size

    It just came to me about my confusion here a few years ago concerning the axle for 3/4" or 1" spindles. (Actually July 2017 was four years ago, wow.) The steering knuckle bolt holding the knuckle to the axle is the same size! SO, I didn't need to swap out an axle, which I did! I swapped out my...
  7. gloughery

    Let clutch out in neutral to shift

    Hello, I have to let the clutch out on my 122 before changing gears most of the time, then it is no problem to change gears that one time. I also notice my driveshaft is spinning faster (gears grind and teeth fly) before I do the neutral thing as well. My throw out bearing needs an adjustment...
  8. gloughery

    UR or UL battery terminals

    I am following Charlie’s advice and ordered an Interstate C75DT-XHD battery and not sure if a right-side positive will fit all 169 and older IHCC’s. I looked at all of mine and there is a mix of UL and UR but I see hints in older wiring that the positive is on the right. I need this for a 70...
  9. gloughery

    Worn bearing hole on wheel

    Howdy, any advice on how to tighten up a worn hole on a wheel? The picture is a front wheel, but the bearing does not fit tight and it spins freely. On the lower left you can see where PO must have tried to tighten it by making an ident, but it didn’t work. How do I fix this the right way...
  10. gloughery

    Yale-Towne 1-ton (BB) Hoist

    Lot's of reasons to stay inside so I am pulling some preventative maintenance. I am cleaning up an old spur-geared 1-ton hoist and want to re-grease the gears inside the gear box. How do I remove these horizontal pins to the left of the zerk fitting (hole, zerk removed)? The pins don't go...
  11. gloughery

    Archive through August 10, 2017

    Ethan, that's exactly what happened. I don't have a 1" open end thin enough to hold the top nut. I slowly turned the bottom nut. My arm was blocking my view and I stopped to take a look and POW! In addition to thin open ends, I also need thin-walled sockets and good snap ring pliers. And the...
  12. gloughery

    Archive through July 17, 2017

    Thanks Charlie, I'll pay attention to that. I also found a spring assist inside the frame with the 3 point lift, so this is perhaps more than just a nice parts tractor. I may have to change the oil and put in some fresh gas to see if I can get this started. This is how my last two CC's have come...
  13. gloughery

    Archive through June 26, 2017

    Thanks David, there is a sleeve that goes over the bolt (caliper spacer) that sets the space between the calipers, also under the spring. The whole assembly is loose on the bracket and I'm thinking shims, but these parts aren't flimsy sheet metal and should fit better than this.
  14. gloughery

    How to remove CC42 snow thrower auger?

    Howdy all, I have a CC42 for a 122 and want to remove the auger to replace the bearings. How do you get it out without cutting or bending anything? Thanks!
Back
Top