• This community needs YOUR help today. With the ever increasing fees of everything (server, software, domain, e-mail) , we need help. We need more Supporting Members, today. Please invest back into this community to help spread our love and knowledge of IH Cub Cadets. You get a lot of great new account perks including access to private forums. If you sign up for annual, I will ship a few IH Cub Cadet Forum decals too in addition to all the account perks you get. You can see what it looks like below.

    Sign up here: https://www.ihcubcadet.com/account/upgrades

Search results

IH Cub Cadet Tractor Forum

Help Support IH Cub Cadet Tractor Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. B

    1450 barely backup up after Neutral Adjust.

    The speed control level on my 1450 has been out of adjustment since I bought it in 2020. As the image shows, the tractor's neutral (as far as the pump trying to move the tractor forward or reverse) was when the lever was in the position shown in the picture. I have been reading our website's...
  2. B

    Everyone, I need some troubleshooting advise - 1450 starter "died"

    I drove the tractor into the garage and was checking the hytran fluid level. I went to put it away and the starter wouldn't turn "like it died." Listed below are what I've tried and what I discovered. 1) The starter solenoid "clicks" when the key is turned 2) The starter solenoid does NOT click...
  3. B

    QA36A Snow Blower Bad Shaft

    I bought this snow blower a while back and when I connected it to my 1450, I thought it had bad U-Joints. I bought them "Very Pricey" and took the shaft out and I have discovered that the output shaft on the right angle gear has the key way wallered out. Is it worth taking to a machine shop to...
  4. B

    15 ho kohler command for a 782

    I am going to look at this kohler motor that was in a cub cadet. He said he bought it to put on a go cart and never got around to it and it’s just sitting taking up space in the garage. I’m needing a replacement engine for the kohler series 1 17 hp in a 782. I have two questions. 1) Are these...
  5. B

    Mid 90s Briggs engine swap

    Has anyone tried to install a Briggs 16 horse twin out of a 1641 into a 782? The most obvious issue is that the Briggs has a fuel pump on it and the tank sits under the rear fender and the old Kohler K17’s fuel is gravity fed from the tank ride behind the engine. I picked up a 782 last night...
  6. B

    44A deck pulley issue

    Everyone, I’ve tried to look for this problem on this site and I cannot find anything relevant. This pulley has play in it. The bearing runs smooth and is not building heat when I mow so I’m confident it’s ok but either the pulley has wear or the bearing shaft has wear. 1) How does it come off...
  7. B

    Sold QA36A snow blower part needed

    Does anyone have the belt tensioner bolt assembly that I can buy? I purchased a snow blower and the adjustment assembly has the threads messed up on the adjustment bolt and I can’t tighten the pulley.
  8. B

    Mule drive pulley out of alignment

    Gang, I lost a pto to deck belt a few weeks ago and after replacing it, I noticed that the new belt jumped off the idler on the mule drive as soon as I engaged the pto. Both pulleys seem to be perfectly vertical but the one with the spring acts like it has slid over to the center a little bit...
  9. B

    Mid ‘70s 1450 Hydro Linkage worn?

    I purchased this 1450 cub to mow the lawn at our new home. It’s a great mower as I expected it to be. I grew up using a 1200 three speed. I almost wrecked this mower when it took off and the speed control wouldn’t slow the machine down. I just removed the cover and I discovered that the linkage...
Back
Top