• This community needs YOUR help today. With the ever increasing fees of everything (server, software, domain, e-mail) , we need help. We need more Supporting Members, today. Please invest back into this community to help spread our love and knowledge of IH Cub Cadets. You get a lot of great new account perks including access to private forums. If you sign up for annual, I will ship a few IH Cub Cadet Forum decals too in addition to all the account perks you get. You can see what it looks like below.

    Sign up here: https://www.ihcubcadet.com/account/upgrades

Search results

IH Cub Cadet Tractor Forum

Help Support IH Cub Cadet Tractor Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. B

    Everyone, I need some troubleshooting advise - 1450 starter "died"

    One last update- it was actually corroded ends on the starter wire at the solenoid. I cleaned the ends on the wires, ground connection between the block/starter and both battery terminals. Before I put it all together, I coated the ends with no -ox electrical contact grease and it started fine.
  2. B

    Everyone, I need some troubleshooting advise - 1450 starter "died"

    I’m happy to report that I have isolated the problem. It’s the 12volt wire going from the solenoid to the starter. Thanks everyone for the valuable input!
  3. B

    Everyone, I need some troubleshooting advise - 1450 starter "died"

    I want to thank everyone for the advice. It helps to have a wealth of knowledge to pull from when you have an issue here and there. The earliest I can do anything is Wednesday. I’m anxious to get into it and see what’s going on.
  4. B

    Everyone, I need some troubleshooting advise - 1450 starter "died"

    I believe the solenoid is located under the dash. That's what I hear clicking when I turn the key to "start." Is the best way to get access to it is by removing the gas tank?
  5. B

    Everyone, I need some troubleshooting advise - 1450 starter "died"

    Gary, the starter solenoid is located under the dash. I believe that is what I hear clicking when I turn the key to start.
  6. B

    Everyone, I need some troubleshooting advise - 1450 starter "died"

    Thank you, I’ll take it off in the next few days and investigate further.
  7. B

    Everyone, I need some troubleshooting advise - 1450 starter "died"

    I drove the tractor into the garage and was checking the hytran fluid level. I went to put it away and the starter wouldn't turn "like it died." Listed below are what I've tried and what I discovered. 1) The starter solenoid "clicks" when the key is turned 2) The starter solenoid does NOT click...
  8. B

    QA36A Snow Blower Bad Shaft

    I bought this snow blower a while back and when I connected it to my 1450, I thought it had bad U-Joints. I bought them "Very Pricey" and took the shaft out and I have discovered that the output shaft on the right angle gear has the key way wallered out. Is it worth taking to a machine shop to...
  9. B

    Tractor For Sale Tractors, Attachments, Parts for Sale

    I see some pics for snow blowers. I have a QA36A single stage blower that has a bad shaft on the right angle gearbox. I see your dad has some blowers and one pic of a "loose" gearbox. Does he still have it.
  10. B

    15 ho kohler command for a 782

    Thank you for the VERY HELPFUL information. You did a nice job on you install!
  11. B

    15 ho kohler command for a 782

    I am going to look at this kohler motor that was in a cub cadet. He said he bought it to put on a go cart and never got around to it and it’s just sitting taking up space in the garage. I’m needing a replacement engine for the kohler series 1 17 hp in a 782. I have two questions. 1) Are these...
  12. B

    Mid 90s Briggs engine swap

    Has anyone tried to install a Briggs 16 horse twin out of a 1641 into a 782? The most obvious issue is that the Briggs has a fuel pump on it and the tank sits under the rear fender and the old Kohler K17’s fuel is gravity fed from the tank ride behind the engine. I picked up a 782 last night...
  13. B

    Parts For Sale 44c mowing deck

    Did you sell this mower deck?
  14. B

    44A deck pulley issue

    Everyone, I’ve tried to look for this problem on this site and I cannot find anything relevant. This pulley has play in it. The bearing runs smooth and is not building heat when I mow so I’m confident it’s ok but either the pulley has wear or the bearing shaft has wear. 1) How does it come off...
  15. B

    Sold QA36A snow blower part needed

    H Thanks for letting me know about Jeff’s parts. I found one on eBay and it arrived today however I looked at his stuff and I’m glad he is offering so many things. I’ll be needing more stuff. Thank you!!!
  16. B

    Sold QA36A snow blower part needed

    I had to put heat on the round adjuster nut to get it to move. In fact I had to keep re heating it to get it to move. As you can see from the photos, I had to grab it with vise grips to hold it tight enough to get it to move. If I knew the thread count, I would order and left handed thread tap...
  17. B

    Sold QA36A snow blower part needed

    Does anyone have the belt tensioner bolt assembly that I can buy? I purchased a snow blower and the adjustment assembly has the threads messed up on the adjustment bolt and I can’t tighten the pulley.
  18. B

    Mule drive pulley out of alignment

    Greg, thank you for the help. The picture from your manual that you posted was the biggest eye opener. Someone put the pulley on the wrong side and I’ve been using for 2 years that way.
  19. B

    Mule drive pulley out of alignment

    I got it put together correctly. I replaced the idler pulleys while I had it apart. Thank you for the advice!
  20. B

    Mule drive pulley out of alignment

    As I study the picture that Greg attached, it appears the the spring assembly is like mine but my pulley is on the wrong side of the bracket. Can anyone tell me what is the measurement between the two pulleys?
Back
Top