• This community needs YOUR help today. With the ever increasing fees of everything (server, software, domain, e-mail) , we need help. We need more Supporting Members, today. Please invest back into this community to help spread our love and knowledge of IH Cub Cadets. You get a lot of great new account perks including access to private forums. If you sign up for annual, I will ship a few IH Cub Cadet Forum decals too in addition to all the account perks you get. You can see what it looks like below.

    Sign up here: https://www.ihcubcadet.com/account/upgrades

Search results

cadet connection
xtreme motor works
kirk engines
cub cadet used parts
IH Cub Cadet Tractor Forum

Help Support IH Cub Cadet Tractor Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. abthomas

    Why won't my tractor run??????

    Hopefully it didn't fill the crankcase with gas !
  2. abthomas

    Slow Cranking K241

    I would run it for 10 min or so, shut it down and let it cool completely then re-torque because they always loosen up after a run cycle with a new gasket. I usually re-torque 3 times after a rebuild, It likely starts quicker with the work you've done but it didn't make the starter /gen spin...
  3. abthomas

    169 hydro valves stuck in

    usually I just clamp them upside down in the vise and take a small pin punch through the hole in the bottom and tap the ball, normally they are not stuck very tight ,once free clean the pins ,spray some lube and work them up and down by hand using the pin punch on the bottom and finger on top...
  4. abthomas

    CC 125 hydraulic lift pump.

    Before disassembly !
  5. abthomas

    CC 125 pto clutch removal

    you could use a cut off wheel or a die grinder just don't booger the crank too much ! cut most of the way and try a hammer and chisel and it should split ! If I remember the collar has a short bolt and jam nut and an allen set screw . You need a small cut off wheel to get in there possibly on a...
  6. abthomas

    CC 125 pto clutch removal

    are you talking about the allen set screws in the 3 holes around the outer perimeter of the clutch,2 screws per hole ? or the locking collar that holds the pto brg to the crank ?
  7. abthomas

    1811 Charge pump shaft repair

    would be hard with shaft in the pump and welding may cause the internal bearing to arc ?
  8. abthomas

    1450 project

    Welded up the trunnion damper spring fit which was badly worn to one side , had about 45 min in the repair . I use a copper bar on the bottom ( the weld doesn't adhere to the copper ) for a backer strip then mig it back to size. A die grinder and file finishes it up. It is 1 3/16 long x 3/4...
  9. abthomas

    1450 project

    Re-installed the hydro pump, next up weld the damper spring trunnion bracket !
  10. abthomas

    1450 project

    Finally getting around to the 1450 I bought about a year ago ! Starting with the hydro gasket to the rear end leak, posting some pics for those that have never done one . I loosened the brake hardware and pulled this one up through the tunnel, afterwards I removed the fender pan for better...
  11. abthomas

    K301 rebuild

    float level set ok ? I had the screw that holds the points wire strip out and short against the cover also when rpms went up ?
  12. abthomas

    K301 rebuild

    I once had a bad plug wire cause the same issue ! would idle and rev to about 1/2 throttle then stumble and backfire !
  13. abthomas

    Loose Steering on Narrow Frame Cubs

    C but don't over do it or it will start to bind but also expect some free play is always present on these old tractors ! take a good look at diggers post for a understanding of what all is there and what all could be worn !
  14. abthomas

    Do I have a leaky head gasket?

    I normally re-torque the head 2-3 times after a rebuild, run it long enough to heat up, let it cool down completely and torque it , you'll find it's loosened up from the original torquing ! call me anal but iv'e never had to revisit a leaking head gasket !
  15. abthomas

    K301 rebuild

    I have purchased several kits on ebay from bakt4kids and have not had any issues with them ! I do not replace the balance gears when doing a rebuild .
  16. abthomas

    1973 128

    good number , google it and lots come up ! nice used ones are pricey !
  17. abthomas

    1X9/8 Grille insert springs

    looks good to me !
  18. abthomas

    Vermeer M 147H PTO questions

    It use to be not so long ago one could pick up a good used pto for a reasonable price ,not the case any longer like everything else they want a hefty price for one that needs complete rebuild and the parts to rebuild are getting ridiculous !Rebuilt ones are going for around $ 200 + so once you...
  19. abthomas

    Vermeer M 147H PTO questions

    It does appear that #15 is broke off part way and the #19 fingers that go into the recess on 15 are rusted off on the ends and likely will not be any good even with a new #15 button ,part 16 just pushes into the hole in #21 and most time only the piece in the hole is left as the pto ate the rest...
  20. abthomas

    Part # for throttle shaft repair kit

    I believe this is what I use from mcmaster carr , McMaster-Carr but shipping will be way more than the bushings !
Back
Top