• FIRST AND LAST NAMES ARE REQUIRED WHEN REGISTERING

Search results

kirk engines
Shop deals on ebay
shop deals on amazon
cub cadet used parts
IH Cub Cadet Tractor Forum

Help Support IH Cub Cadet Tractor Forum:

  1. J

    Archive through May 24, 2014

    1981 782. This is an older restoration I took it down to the bare frame and repainted everything about 5 years ago. It has some scratches from use these days. This is what I put in it when I restored it. New driveshaft and rag joints. 1811 steering gear. The steering linkage has all heim joints...
  2. J

    Archive through March 30, 2014

    The hitch and weight bracket are sold pending funds
  3. J

    Archive through March 30, 2014

    Brinly box blade modified. I added a heavy steel bucket edge to the bottom of the blade, added bigger sides, and scarifier teeth. Also not seen in pic is a post on the top back to stack weights so it can do the work. sorry for the poor pic. I will get it dug out soon. I used it to level out 100...
  4. J

    Archive through March 30, 2014

    Custom front weight bracket and weights. Made out of a mule drive to fit wide frames or 82 series. 4 30lb weights. fits on your tractor just like a mule drive. Quick to take on and off. Perfect for the light in the nose 82 series. $120 picked up in Cedar Rapids. Will not ship this item.
  5. J

    Archive through March 30, 2014

    Brinly sleeve hitch adaptor. floating and non floating lift straps, double bracket for the rear end, pins, etc.. everything shown in this pic. Hitch is not bent or twisted. $125 picked up in Cedar Rapids. I will ship at additional actual cost. Please respond to email.
  6. J

    Archive through March 19, 2014

    Brinly sleeve hitch adaptor. floating and non floating lift straps, double bracket for the rear end, pins, etc.. everything shown in this pic. Hitch is not bent or twisted. $125 picked up in Cedar Rapids. I will ship at additional actual cost. Please respond to email.
  7. J

    Archive through March 19, 2014

    Tires are sold....Thank You!!
  8. J

    Archive through March 19, 2014

    Vredestein V61 tires 16x6.50x8 with tubes. All are new and never used. Dirty from sitting around in my garage. $80.00 for all picked up in Cedar Rapids.
  9. J

    Archive through May 07, 2013

    For Sale: Brinly Sleeve Hitch 10" Moldboard plow. Some light surface rust on painted beam and plow face and coulter. Good point, plows great. Contact for pics. [email protected] $150 picked up in Cedar Rapids, IA This picture is a couple years old the shiney parts are a...
  10. J

    Archive through July 29, 2009

    Found my tiller. Thanks guys
  11. J

    Archive through July 29, 2009

    WANT TO BUY..... Tiller and gearbox to put on my 782. I would prefer a #2 with the 5/8 belt pullies, but would consider a 1A with extensions and do my own conversion. Also am looking for a later 5/8 mule drive for the same 782 Somewhere within 200 miles of eastern Iowa only. Thanks...
  12. J

    682 Axle Question

    generally the cast rears have the coarse splines. However that may vary as I have a 782 with a cast rear end and it came with fine spline axles. If you have a spare rear end out of the tractor it would not be too hard to pull the cover off and check. then you would know for sure.
  13. J

    82 series front weight bracket

    Thank You for all of the compliments. This mini project was fun and easy. Now if I could just find all of the parts to build a Cat 0 plow.
  14. J

    82 series front weight bracket

    Here are the finished pics as promised
  15. J

    82 series front weight bracket

    The weights I use on the rear are just like the ones on the box blade. I just transfer them back and forth depending how much weight I need on the blade at the time. I have 2 cross braces and a 1" threaded rod in the center of the rear wheels which I can hang whatever weights I want on at...
  16. J

    82 series front weight bracket

    on a semi-related note here is a so so picture of the box blade I am using. I made it from a Brinly 42" rear scraper blade.
  17. J

    82 series front weight bracket

    Here are some pics of the bracket finished except for paint. I built it spcifically for the weights which were from an automotive parts rack. I was originally going to use a rod with pins to keep the weights on. Now I think I will bolt them as they have more swing and wobble than I like...
  18. J

    82 series front weight bracket

    I agree. The second rod adds alot of weight bearing piece of mind. Also the holes in the frame were already there so I figured I might as well use them. I modeled it after a CCC factory weight bracket that I found but did not buy because the price was too high. It had locking pins that...
  19. J

    Archive through October 16, 2007

    Parts are gone pending pick up thanks
  20. J

    82 series front weight bracket

    Thought I would post a couple pics of the front weight bracket I am making for my 782. I am going to cut the bottom part of the old Mule drive off after I get the front piece welded on. I've been using my 782 with a box blade and the nose of it gets light enough sometimes that it does not...
Top