• FIRST AND LAST NAMES ARE REQUIRED WHEN REGISTERING

Search results

IH Cub Cadet Tractor Forum

Help Support IH Cub Cadet Tractor Forum:

  1. B

    Mikes Very Own 169 Refurbish

    Yes they were and it still did it for ours anyway.
  2. B

    Mikes Very Own 169 Refurbish

    That is because of two things. First the cooler the air is the more dense it is which makes it harder to compress, and second motor oil gets thicker as well. Kohler wants the ACR to open the exhaust valve .031 to .042 they also say the tab can be bent only four times before it will break.
  3. B

    Mikes Very Own 169 Refurbish

    If your cub cadet cranks and then stops then the ACR isn't releasing enough compression. I was working on my cousin's 1450 and it would do the same thing. We were rebuilding the motor and found out the ACR tab was bent down further than the parts motor we have. We swapped the cams while we were...
  4. B

    UR or UL battery terminals

    Interstate batteries and everstart are both made by johnson controls.
  5. B

    K321 Laboring hard after warming up

    If changing the head doesn't fix the issue check camshaft\crankshaft end play, tight tolerances can cause similar symptoms. Hth
  6. B

    Archive through August 17, 2019

    Maybe it has a 1 inch thick steel plate as the trailer bed.
  7. B

    Archive through May 16, 2019

    How do you open the hood on that original?
  8. B

    Archive through May 16, 2019

    I am 90% sure that is a 3800 backhoe loader, 4100s have different fenders than that one has.
  9. B

    Archive through May 11, 2019

    Hey guys my cousin has a 1450 cub cadet that will idle but if you try to rev it up it just stumbles. We rebuilt the carb cleaned all the passages out of it we used wire, drill bits, carb cleaner, and compressed air. The coil was also changed and fuel is flowing nicely to the carb. What else...
  10. B

    Archive through April 30, 2019

    How far do you tighten down Charlie's new and improved isomounts? I thought i read about it before but can't find it now. Oh and thanks for the parts Charlie.
  11. B

    Why did cub cadet make a 1282?

    Okay, thanks that makes sense.
  12. B

    Archive through April 15, 2019

    Earl L I think the throttle cable from a 1486 IH could work they are pretty heavy duty. They have a L shaped end on one side and the other end is threaded for a ball joint.
  13. B

    Why did cub cadet make a 1282?

    Why did cub cadet make 1282s and the following k301 12hp models? Did they have a ton of extra motors left over? If not why didn't they power them with k321s or k341s?
  14. B

    Archive through April 26, 2018

    Patrick, I think you found the problem then as loose screws will cause the gasket to leak. Get a gasket kit for it and add or remove gaskets til you get between .003 to .020 crankshaft end play. It is also a good idea to change the seal while you have it apart. BTDT
  15. B

    Archive through April 26, 2018

    Patrick, how fast does it leak? If it doesn't leak too fast you could probably mow with it just watch it and check the oil level every 5 to 10 minutes. Most likely it's the seal there isn't much else back there to leak. There is a gasket behind the bearing plate that could also leak in a way...
  16. B

    Archive through April 23, 2018

    We use Nutra-sol tank cleaner with 160 degree hot water to clean the tank then solder the tank at the farm my uncles own. We leave the nutra-sol overnight sometimes repeated depending how bad the tank is. Nutra-sol is really for cleaning ag sprayers but it dissolves rust. After draining the tank...
  17. B

    Archive through April 17, 2018

    Okay, Thanks guys }
  18. B

    Archive through April 17, 2018

    Hey guys new member here, I have been reading for about a month though. My Uncle Davy has a Cub Cadet 169 that turns over slowly. He has replaced the battery and tried adjusting the ACR but broke the tab doing so. He replaced it with a different one but it still turns over slow. Does it probably...
  19. B

    Archive through March 19, 2018

    Jeff Belliveau one of my late grandpa's Cub Cadet 1450 does the same thing even with the relief valve buttons depressed but grandpas other 1450 doesn't I wondered if it has to do with the hours on the tractors, the one that moves easily has a lot less hours considering minimal wear on the...
Top