• FIRST AND LAST NAMES ARE REQUIRED WHEN REGISTERING

Search results

IH Cub Cadet Tractor Forum

Help Support IH Cub Cadet Tractor Forum:

  1. J

    2182 charging problems ?

    I have a 2182 that has never showed any problems. Went to start, and nothing. Put a voltmeter on battery & only 8 volts. Has only sat for a week. Put another battery in & it started up just as always. Put voltmeter on battery & it's jumping up & down. Not steady at all. As high as 18 volts...
  2. J

    1641to hyd steering.

    Its 1862 then.
  3. J

    1641to hyd steering.

    Sorry. It is an 1862 or1864. Just haven't checked the serial #.
  4. J

    1641to hyd steering.

    I have a 1641 in nice useable condition. I also have a 18?? with hyd steering. It's been used hard & not maintained. The motor is hurt. Would like the hyd steering on the 1641. For those of you in the know. What would be the best way to go about it? Steering tower from 18??& parts to 1641 . Or...
  5. J

    Electric clutch engagement

    Try taking wire plug of switch. Spray with WD40. put back on & off a few times. Get a good connection again. If not try the do same at seat safety switch . Then at connection at PTO.
  6. J

    2084 snowblower width

    I seen that on Face Book . Hope ya got it cheep. It may be better that it look's.
  7. J

    Compression check on 18 magnum.

    Warm Or cold . At least it gave me an outlook that the valves were sealing & it didn't have a hole in a piston. Like I said it had about 70PSI in both cylinders. Air cleaner off & throttle open.
  8. J

    Compression check on 18 magnum.

    Need to get running first. Was told its been sitting for years. So as the carb was sitting in cleaner & I was checking other pieces of the puzzle . Its just 1 of the things I did. I am now at , no spark. So something else to chase the reason for .
  9. J

    Compression check on 18 magnum.

    Well, Thank you. I was not aware of the free download. So I guess at 70psi I should count this 1 as almost done . Think I try another gauge first . Then give it a squirt of oil or two & see what kind of difference I get.
  10. J

    Compression check on 18 magnum.

    Doing a compression check on an 18 magnum. What would be the average acceptable psi be for one with about 900hrs on it.
  11. J

    Seats !

    Now ,that's what I'm talking about. Just still looking for something with a bit more comfort than what the original has.
  12. J

    Seats !

    I have a few Cubs . They are 1440/ 1541/1641/1811/1864/1882/2182 & I think my biggest dislike other than the plastic , is the seats. I like the metal on the 1811. I also have a seat on the 1811 from Northern Tool. I like that the best. But the arm rest are stationary & makes it harder the get...
  13. J

    1882 value?

    I have 1. It has 18 Kohler magnum motor & not the command that you show in that one. From the little I know. They are a very solid & reliable tractor. Must be careful with plastic hood & side panels. Check brake pads. That model has steering brakes. Depending on how it was used ,they may be...
  14. J

    What the ???

    Thank you for the service bulletin. Wheels do spin freely when lifted off ground. So brakes are adjusted ,ok.. I will check better as soon as I can swap tractors. I now have 1882 w/snow blower on it &2182 w/plow on it where they have heat for easier starting & repairs ,if needed. That 1 has...
  15. J

    What the ???

    Filter is fresh & so is oil. Don't have a factory service manual. Also with top plate off so ya can look at linkage all looks the same as the others.
  16. J

    What the ???

    I have two 2182's & 1882 One of the 2182's does not have the ground speed of the other one. The other 2182 seems to be evenly matched with the1882. I also have a 1541,1641,1862 & 1811 . They all seemed very equal except for the one 2182 . Were their different rear end gears available ? It...
  17. J

    1811 magnum to command.

    Have an 1811 looking to put a command 20 in it. What's needed to do? How many changes ?
  18. J

    Big Mower Decks- Opinions???

    I use a 60 Haban under a 2182. No complaints from me. Keep it greased & clean with sharp blades. I also let the mower wheels just skim the ground. I cut quite a bit of grass. I am also towing a 60" Swisher off set behind tractor. So I'm cutting almost 10' at a time. The 2182 get's a good work out !
  19. J

    Frame supports for SGT.

    Thank You. I ordered a set.
  20. J

    Frame supports for SGT.

    Has anyone used frame supports from Extreme Motor works ? If so does the front facing one fit with the mounts for a Haban plow ? They look like they may overlap each other .
Top