• FIRST AND LAST NAMES ARE REQUIRED WHEN REGISTERING

Search results

Help Support IH Cub Cadet Forum:

  1. glippert

    Parts For Sale New Seat for Ultima ZT2 54

    Selling for my brother-in-law: New, never used, adjustable seat from an Ultima ZT2 54" zero turn. The dealer made a mistake with the deal, so he offered an upgraded seat (premium, extra high back, wrap-around) at dealer cost to make up for it. However, he wouldn't give any credit for the...
  2. glippert

    Parts Lookup Broken?

    I'm having trouble with the Parts Lookup, and wondering if it's operator error or Cub Cadet's error? I can get to the "Lookup Parts Via Diagram" page, but the little box where you choose CCC/MTD or IHCC never shows up. And if I search for a tractor model like 1450 or 782, it looks for part...
  3. glippert

    Lock Washers

    It's no secret that all of you are probably a lot smarter than me about such things, so I'll ask my question here. Cleaning up a little today, sorting nuts, bolts washers, etc, and it occurred to me that I don't know the proper use for various lock washers. Inside star vs outside star? Star vs...
  4. glippert

    Mystery Lift Bar and...

    I'm splitting my 782, to replace the seals in the hydro pump, repair the trunion slot, etc. I was surprised to see that the 3 point lift bar is not straight. And it doesn't have just one bend - it looks like a meandering river, with two bends, first up, then down. Does anyone know what...
  5. glippert

    782 Hydro Leak

    I finally decided to believe that Spring is here, and I removed the snow thrower (QA42A), chains, wheel weights, and rear weights from my IH 782 (s/n 682355). And, since it will be a little while before I need to install the tiller, I decided to finally change the cork gasket to cure my hydro...
  6. glippert

    1650 Starter Gear

    Looking for a good 10-tooth pinion gear for a Quietline starter (1250, 1450, 1650). Must be in good condition - no chipped/broken teeth.
  7. glippert

    1650 in Tough Shape

    This probably won't be a full refurb, but I know I'll have a lot of questions, so I decided to just start a new thread for it: I'm finally getting around to working on a 1650 I got about three years ago. It came with the motor removed, along with everything else under the hood (gas tank...
  8. glippert

    1250 Drive Shaft Flange Assembly

    I don't see the disclaimer anymore that there are no stupid questions, so this might be one. The flange assembly that attaches to the cup on the flywheel (just outside the grass screen) has a bushing that centers the drive shaft. Should the outside of that bushing be lubed with anything? It...
  9. glippert

    1250 Drive Shaft Flange Assembly

    I don't see the disclaimer anymore that there are no stupid questions, so this might be one. The flange assembly that attaches to the cup on the flywheel (just outside the grass screen) has a bushing that centers the drive shaft. Should the outside of that bushing be lubed with anything? It...
  10. glippert

    Manual Lift Arm

    According to FAQ #78, the top thumb button should unscrew from the rod in the manual lift arm. Is this the same on all models? The top button and the rod of my grandson's 1250 work fine, but the bottom L-bend is worn pretty thin by the ratchet, so I'd like to have it built up, or maybe even...
  11. glippert

    Brake Parts for 1250

    I'm looking for a pair of good used brake stators (#18 below),preferably with usable brake pads still on them, and a shoulder bolt and nut (#20/21 below). Somehow, my grandson lost these parts from the left rear wheel on his 1250.
  12. glippert

    Is there a prize?

    Is there a prize for the worst follower stud in a steering box? My grandson's 1250 had extremely sloppy steering. In addition to front wheel bearings falling apart, I found the follower very loose. I removed the sreeting assembly, took off the lever plate and found this: No wonder it...
  13. glippert

    Draft thread?

    I started a thread, then hit a wrong button and found myself back at the main forum page. Is my "draft" thread saved somewhere, where I can preview & post it?
  14. glippert

    Archive through February 05, 2019

    Ron S - Great description of the cork gasket replacement process. I've got it saved for future reference. What a great forum!
  15. glippert

    Archive through July 06, 2016

    Looks like Charlie will be having a rebuilt PTO sale one of these days. You know, since he has nothing else to do all day! (Imagine a "Poking the Bear" emoticon here)
  16. glippert

    Archive through June 21, 2016

    Harry - Yes, I left the original fuel shut-off on the tank.
  17. glippert

    Archive through June 08, 2016

    When I ordered some parts last week, I was impressed with how quickly I received them. Lo and behold, turns out I forgot a few things, so I put in a new order. Again CC Specialties had the parts to me less than 48 hours after I placed the order. But I do have one complaint: Although Charlie...
  18. glippert

    Archive through March 17, 2014

    Doug & Dave - Thanks for the reply on my hydro valves. Doug - I guess it must have been in the FAQ where I saw it. Thanks for the reminder. Sometimes it sucks getting old! Greg
  19. glippert

    Archive through December 04, 2013

    Dang archive bug! Here's the 5-day forecast that will keep me out of the garage until the heater is fixed!
  20. glippert

    Archive through November 17, 2013

    Mike P - I got my QA-42A out of storage this weekend and into my garage, next to the 782, but it's not mounted yet. And despite the IH marketing that Charlie posted, it takes me a lot more that a few seconds to get it mounted. Each year, when I finally get it on, I think I'll remember the...
Top