Kirk Engines, Inc Cub Cadet Used Parts CADET CONNECTION Cub Cadet Specialties Cub Cadet Specialties

Search results

Help Support IH Cub Cadet Forum:

  1. mgonitzke

    Front steering knuckle bolt size

    1330 is a lawn tractor, not a garden tractor, and has a completely different (smaller) axle.
  2. mgonitzke

    motor hoist idea

    This worked for me: Engine stand + small floor jack + some other odds and ends.
  3. mgonitzke

    Front steering knuckle bolt size

    Yes, the axle castings are the same between a 169 and 782. Only difference is the spindle itself.
  4. mgonitzke

    New to me "sad" 782, so I will need lots of help here

    No such thing on a 782...clevis pin behind the one that attaches the hydraulic cylinder to the rockshaft gets replaced with a slightly longer one.
  5. mgonitzke

    New to me "sad" 782, so I will need lots of help here

    For the IH style 3-point with the upper cast piece that pivots in the frame, the lift bar you need is a straight piece of 1/2 x 1-1/2" steel bar stock with a counterbored 1/2?" hole at the front end and 5/8" or 3/4" (can't remember) hole at the back end. There should be a dimensioned drawing of...
  6. mgonitzke

    Just got the 670 predator motor on her.

    You mean other than hacking a big notch in the frame?
  7. mgonitzke

    Cub 100 paint color

    This was PPG mixed to the 901 color code from the FAQ. Definitely had a slight green cast to it, but I thought it looked nice. Take all of these pictures and comparisons with a grain of salt, as your monitor settings and editing of the pictures are going to influence what you see here.
  8. mgonitzke

    2084 Super Garden Tractor won't stay running/gas vanished!

    I would have gotten one of the terminals for larger gauge wire and put the ends of both wires that need to be spliced into one crimped terminal, rather than trying to scab one on in the middle. I now realize you may have taken my schematic more literally than I had intended... Believe it or...
  9. mgonitzke

    CC 2185 Brake interlock switch

    2185 has completely different safety switches than a 682.
  10. mgonitzke

    CC 2185 Brake interlock switch

    It should be one of those, but if I remember right, neither one is actually mounted exactly where the parts diagram shows. It is a giant pain to remove, but easy to install. I worked on one of these a year or so ago and spent a lot of time cussing at that switch.
  11. mgonitzke

    Ammeter ?

    Based on those voltages, that is normal operation. Your ammeter may have gone bad.
  12. mgonitzke

    2084 Super Garden Tractor won't stay running/gas vanished!

    The install instructions for the pump require it to be mounted no higher than 12" from the tank outlet. You are probably borderline exceeding that. I'd make sure tank is clean, fuel lines are, good, etc. first before moving it though.
  13. mgonitzke

    Help wiring up electric fuel pump for my 2084

    I apparently didn't take any pictures when I did this, and the tractor is 50 miles away. Hope this will suffice:
  14. mgonitzke

    Help wiring up electric fuel pump for my 2084

    I just did this on a 2000 series with the same engine...the easiest way is to make a little adapter to plug in where the fuel solenoid connects. Just need a package of bullet terminals and a few inches of wire. I'd add a fuse to it as well.
  15. mgonitzke

    782d battery

    Key switch was on or you have a short somewhere. It should not do that, regardless of whether or not the positive cable was hooked up first.
  16. mgonitzke

    1810 to 2084 rear swap

    Does the hydraulic lift still work? Is the fluid level correct? When is the last time the filter has been replaced? If all of that is ok, it is possible the little pin that drives the charge pump has sheared off. These units are very reliable and it is pretty unusual for them to fail.
  17. mgonitzke

    1810 to 2084 rear swap

    No. 2084 has a different ratio reduction gear, and the hydro pump input shaft is splined, and they hydro is ported. 1810 has a round shaft for a coupling attached with a spirol pin, is not ported for aux hydraulics. You cannot swap the transaxle or hydro unit with that combo and have it work.
  18. mgonitzke

    2084 Super Garden Tractor won't stay running/gas vanished!

    The diaphragm on the fuel pump looks like it has failed, or is about to. Given how dirty the engine is, I would pull the engine and remove the flywheel shroud, etc and clean everything up. It is pretty common to have the flywheel end crannk seal go bad and then the whole outside of the engine...
  19. mgonitzke

    2084 Super Garden Tractor won't stay running/gas vanished!

    That is a vacuum pump. Could be rebuilt, but the electric pump I mentioned is still the way I would go. You will need to remove the fitting for the vacuum line in the end cover and plug it with an 1/8" NPT pipe plug when you do the swap. It probably wouldn't hurt to rebuild the carb too. There...
  20. mgonitzke

    2084 Super Garden Tractor won't stay running/gas vanished!

    Facet 40177 is the closest electric pump to the output of the original mechanical or vacuum operated pumps. Cheapest price I was able to find on them was Pegasus Auto Racing's website. In case it wasn't obvious, if it turns out there is gas in the oil, don't run it again until you change the...
Top