• This community needs YOUR help today. With the ever increasing fees of everything (server, software, domain, e-mail) , we need help. We need more Supporting Members, today. Please invest back into this community to help spread our love and knowledge of IH Cub Cadets. You get a lot of great new account perks including access to private forums. If you sign up for annual, I will ship a few IH Cub Cadet Forum decals too in addition to all the account perks you get. You can see what it looks like below.

    Sign up here: https://www.ihcubcadet.com/account/upgrades

Recent content by stanner

cc specialties
Advertise with us
xtreme motor works
shop deals on amazon
IH Cub Cadet Tractor Forum

Help Support IH Cub Cadet Tractor Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. stanner

    149 Taillight Lenses

  2. stanner

    149 Taillight Lenses

    I got mine from a RV parts dealer. not OEM, but they're square
  3. stanner

    QA36A snowblower/thrower wear bar/scraper bar/shave plate

    I made one out of hardware store stock way before Aaron started to make them- worked good
  4. stanner

    Archive through March 25, 2019

    over 100" inches in Oswego north of Syracuse
  5. stanner

    Archive through March 25, 2019

    Someone posted this online, depicting the Blizzard of 1966 in Syracuse NY area. We got something like 60+ inches of snow in a little over a day. the drifts were so high that in places you could touch the lower wires on the power poles. All I remember is my dad opening the garage door to reveal a...
  6. stanner

    Archive through January 19, 2019

    Welcome Tracy! Click on one or more of those rectangular boxes at the top of the page. They’ll help you out and probably have what you are looking for!
  7. stanner

    Archive through December 06, 2018

    Tim M, I have on my 149. the shaft on the kohler was short, so I had to make a bolt-on spacer. need to cut the basket off of the front pulley. controlled with PTO safety switch through a relay so you can't start while energized.
  8. stanner

    Archive through July 03, 2018

    Looks like a 60 desoto
  9. stanner

    Archive through June 06, 2018

    Arron, I've had good luck just removing the inlet tube from the bottom of the case- looses both nuts, case and hydro pump and remove- after draining for the first time, remove rear cover to clean out the boogers inside..... Also, use the proper filter from IH- do not use what Fram says will...
  10. stanner

    Archive through June 03, 2018

    It’s it all that hard to outsmart yourself.....
  11. stanner

    Archive through April 21, 2018

    Mark, there are two in Syracuse NY- Ramsing electric and Ted's Auto Electric- top notch
  12. stanner

    Archive through April 17, 2018

    Bill, chances are that your tiller is worn so that when mounted the big pulley is at an angle. You can try tightening up all of the bolts on the mounting arms, but the holes are prolly wallowed out. I had to put bushings in my tiller to straighten it out. you can adjust pulleys by loosening set...
  13. stanner

    Archive through April 03, 2018

    regarding the Rivnut discussion, these are the cat's meow- not cheap though... I used these to replace the sheetmetal screws on the 149's tunnel cover
  14. stanner

    Archive through March 26, 2018

    Joe P, Since you're in Minneapolis, do I dare say you work for TK? I work for CTD div of Carrier... Used lots of rivnuts.. used them for my 149's tunnel cover ARO makes a nifty tool to set those...
  15. stanner

    Archive through March 05, 2018

    20 years for the BEST dang cub site on the internet!!
See more
Back
Top