• This community needs YOUR help today. With the ever increasing fees of everything (server, software, domain, e-mail) , we need help. We need more Supporting Members, today. Please invest back into this community to help spread our love and knowledge of IH Cub Cadets. You get a lot of great new account perks including access to private forums. If you sign up for annual, I will ship a few IH Cub Cadet Forum decals too in addition to all the account perks you get. You can see what it looks like below.

    Sign up here: https://www.ihcubcadet.com/account/upgrades

Recent content by nbodin

Advertise with us
cc specialties
cub cadet used parts
shop deals on amazon
IH Cub Cadet Tractor Forum

Help Support IH Cub Cadet Tractor Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. N

    Archive through September 01, 2019

    Austin- the splines have to line up with the sliding coupler in the transmission. You can also leave it in neutral, with the clutch pushed down and gently let out the clutch as you put slight pressure on the PTO lever to engage it and it should go right in.
  2. N

    Off Topic For Sale & Wanted Classifieds

    Shultzie- Why not take it to a threshing show and donate it to them?? Be much better off if it gets used once rather than sent back as china crap!
  3. N

    Archive through July 31, 2019

    Paul- could also be a bearing.
  4. N

    Archive through July 31, 2019

    Paul- Bent rim or axle that is bent outside of the spring on that side
  5. N

    Archive through July 31, 2019

    OTF. The Deere dealer is a super place to shop at!! Picked these up last week. I bought the one with the loader and dad got the one with the blower.
  6. N

    Archive through July 05, 2019

    2000 trailer
  7. N

    Archive through May 11, 2019

    Benjamin- The timing could be off
  8. N

    Archive through March 12, 2019

    Jonathan- You sure can. But they will perform better on wider rims. The foot print on the ground will be smaller than if they were on the correct rims
  9. N

    Archive through March 12, 2019

    Mike P. Good find! The original firestones are much better and was told the newer tires are made out of synthetic rubber. I have two new pairs of the 26-12-12 I need to get put on.
  10. N

    Archive through February 21, 2019

    Kraig- Have never tried JB weld for trunion just offered it as something to try. I would not even bother with new springs and caps if there is not at least an attempt to fix the trunion rectangle. I usually cut out the side and weld key stock back in to get to spec.
  11. N

    Archive through February 17, 2019

    Keith- If you can not find someone to weld it for you I would get some JB weld and fill in the worn notches at least. Not the best but better than nothing. Those notches worn in are part of the jumpy operation.
  12. N

    Archive through February 02, 2019

    On the hydros I have done that I have taken the pump off I remove the rearend from the frame, and then block it up so it is sitting on the rear cover. If you just recently changed oil tape the vent shut so it doesn't leak oil. Use the air gun or pressure washer to blow off as much crud as...
  13. N

    Archive through January 26, 2019

    Closed my work for the day. I drive truck. Most of the problems are from all the emission garbage. Mainly DEF freezing. Not worth it in my opinion
  14. N

    Archive through January 22, 2019

    What better to do on a day when it doesn't get above zero degrees! Go spearing after work!!!
  15. N

    I thought 982's were hydros

    They are. More than likely a 982 hood on a 582. The tunnel between your legs should be longer on a 982 and that one looks shorter like a 582 would be.
See more
Back
Top