• This community needs YOUR help today. With the ever increasing fees of everything (server, software, domain, e-mail) , we need help. We need more Supporting Members, today. Please invest back into this community to help spread our love and knowledge of IH Cub Cadets. You get a lot of great new account perks including access to private forums. If you sign up for annual, I will ship a few IH Cub Cadet Forum decals too in addition to all the account perks you get. You can see what it looks like below.

    Sign up here: https://www.ihcubcadet.com/account/upgrades

Recent content by kide

IH Cub Cadet Tractor Forum

Help Support IH Cub Cadet Tractor Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. kide

    Snow Thrower Tangles W/Dog Toy 🤣. This was a Pain in the Ars

    I knew my ears were burning for some reason.. I can't find my original pic of the cord wind incident, glad to still provide a smile....
  2. kide

    Cub Cadet 123 - Hydro Issue

    Make sure you index the pieces so you put it back together the same way as it comes apart.. the late (and missed) Don Tanner had a long thread a few years ago on rebuilding the charge pump in which he rotated the end of the pump 180 degrees.. Didn't work to well..
  3. kide

    Merry Christmas to one and all!

    Merry Christmas Charlie!
  4. kide

    Merry Christmas

    Merry Christmas to all !
  5. kide

    Chirping sound

    If it's doing it under increasing load or when starting it cold, it could be a leaking headgasket:(..
  6. kide

    Engine Overhaul

    Tried to find it, no luck. Tip: Check the crank where the oil slinger is pinned to the throw - I had to replace the crank in a '58 8HP that broke across the throw where the pins were.. (Probably my fault, good running engine, but I was lugging it too much). Dennis Carpenter Cushman Catalog...
  7. kide

    Tie rod ends

    The used ones I've found were, ahh ..... used. Worn enough in the center of the worm to bind on the end of travel if adjusting the slop out in center of travel :( . I considered the possibility of just regrinding to the bring it back clean and same size from end to end with a profiled stone...
  8. kide

    Tie rod ends

    Now if we could get someone to refurb the steering shafts (Digger-know anyone with a sprayweld and cnc grinder setup?)
  9. kide

    Trial Run

    I hope it's an M8 and not one of those Godforsaken OMC things! Flatheads Rule!!!!!!!!! ( my '56 Eagle now has a Vanguard in it, but my heart is still with the Husky :) ).
  10. kide

    Vtwin in a cub

    How was the PTO end? Bolt on or easy to adapt?
  11. kide

    QA36A snowblower/thrower wear bar/scraper bar/shave plate

    You can tell that auger has never seen a gravel driveway!
  12. kide

    Original Cub Cadet High Altitude Carburetor

    Just a thought, I'd try lowering the float level (not drastically), as that does affect the fuel/air mixture (the lower the level, the required suction to pull fuel into the venturi is greater). If it's an older carb with a high speed adjustment, turn it in a little to lean it up.
  13. kide

    Look what followed me home this weekend.

    I learned that with my drill press. Luckily, I can move it around.. I can't believe the condition of the ways on it, David, looks freshly scraped!
  14. kide

    Welcome !

    OK- cause now I got questions... where's the link to Cubfaqs and the "manuals" link isn't manuals.. I assume this is still a work in progress (and I give my whole hearted support to you - I spent 40 years in IT on big iron, networks and later on remote management of about 52,000 desktops) ..
  15. kide

    S/G

    Yes, and there should be felt inside that holds the oil IIRC.
Back
Top