• This community needs YOUR help today. With the ever increasing fees of everything (server, software, domain, e-mail) , we need help. We need more Supporting Members, today. Please invest back into this community to help spread our love and knowledge of IH Cub Cadets. You get a lot of great new account perks including access to private forums. If you sign up for annual, I will ship a few IH Cub Cadet Forum decals too in addition to all the account perks you get. You can see what it looks like below.

    Sign up here: https://www.ihcubcadet.com/account/upgrades

Recent content by kconway

IH Cub Cadet Tractor Forum

Help Support IH Cub Cadet Tractor Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. kconway

    SOUTH BEND LATHE

    South Bend lathe for sale. Comes with everything needed to start turning, will even include the heavy desk that it is mounted too. Pick up only, southwest Michigan. $1,200.00 or best offer.
  2. kconway

    Front wheel bearings for 104

    Thanks Digger. I saw those on your site after I posted the question.
  3. kconway

    Front wheel bearings for 104

    Need to know size and where I can buy front wheel bearings for a 104. Thanks in advance.
  4. kconway

    Archive through February 02, 2019

    David, thanks! I knew there was a place that has been mentioned on here before but couldn't remember it!
  5. kconway

    Archive through February 02, 2019

    Thanks guys! I looked in the parts lookup but didn't find them. Any suggestions on where to get those? Ace Hardware? Lowes? Thanks again!
  6. kconway

    Archive through January 30, 2019

    Snowthrower question - It's a QA36. Does a roll pin fit in the empty hole in the photo? If so, what size? Thanks!
  7. kconway

    Archive through September 27, 2016

    Steve B. - Thanks for letting me know the braces don't have to be square to the thrower. I'll put them on as is and not worry about it. That will save me some work. Thanks again!!
  8. kconway

    Archive through September 27, 2016

    Harry, Steve, The picture I posted showing the spacers on the snow thrower is one someone, probably Kraig, posted a few weeks back. And Steve, you are correct it is a QA36A that I'm trying to mount on my 104. The studs on mine are not long enough to allow the braces to be square to the...
  9. kconway

    Archive through September 25, 2016

    QA 36 question - are the spaces shown below supposed to slip over the pins that are welded to the frame? The pins on mine are not long enough to allow the brace to to be square to the thrower housing. Are those top braces even needed? My original 36" thrower doesn't have them. Thanks in advance!
  10. kconway

    Archive through September 09, 2016

    Thanks Doug for the info. We get a fair amount of heavy wet snow so I think I'll leave them off too. My previous snow thrower didn't have them and it worked fine. I just painted the inside of the shoot with black graphite paint. I've had good luck with that in the past.
  11. kconway

    Archive through September 09, 2016

    Snow thrower question - does anyone use parts 23 and 24 shown in this picture? Do they help or hurt? Thanks!
  12. kconway

    Archive through April 19, 2016

    Doug A., Harry B. - Thanks!!! Harry, I got the picture from the service manual in the manual section.
  13. kconway

    Archive through April 13, 2016

    Doug A., Harry B. - Is this what you're talking about?
  14. kconway

    Archive through April 13, 2016

    How do you adjust the maximum rpm's on a K241 in a 104. I've been moving the throttle cable wire in and out of the little screw at the engine end of the cable. Seems like there should be an easier way. Thanks!
  15. kconway

    Archive through April 09, 2016

    Kenny W. - Thanks for the info! I've replaced the gasket above the glass bowl and it's fine. I've also replaced the "O" ring in the shut off valve but it still leaks. Just tired of messing around with it! As for the filter, the guy at the store said it's supposed to work on gravity feed...
Back
Top