• This community needs YOUR help today. With the ever increasing fees of everything (server, software, domain, e-mail) , we need help. We need more Supporting Members, today. Please invest back into this community to help spread our love and knowledge of IH Cub Cadets. You get a lot of great new account perks including access to private forums. If you sign up for annual, I will ship a few IH Cub Cadet Forum decals too in addition to all the account perks you get. You can see what it looks like below.

    Sign up here: https://www.ihcubcadet.com/account/upgrades

Recent content by John Halper

IH Cub Cadet Tractor Forum

Help Support IH Cub Cadet Tractor Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. J

    I'm bummed out.

    I thought for sure I would get the answer I need, on here. I got some good ideas from this site. It's been very helpful most times. But I needed help on the wiring on 1862 & got nothing. Got a lot of views. But now answers. Took out a 18 magnum & replaced in with 20 command. I don't understand...
  2. J

    1862 wiring diagram

    My name is john. If you could be any help with. 1862 & a wore out 18 magnum. Putting in 20 command. Matching the wiring. I would be very thankful.
  3. J

    Wiring a command to a1862.

    I will try asking this a different way, this time. First, thanks for those that tried to help on previous post. Putting a Command in place of a Mangum. Looking for what wires to connect together. Just afraid of shorting things out. 1862 has 3 pin plug. 2 yellow & black wires together. to1 pin. 2...
  4. J

    18 Magnum to 20 Command in a 1862.

    Thank you for your help. What information I was looking for is. Tractor wiring has 2 yellow & black wires together. 2 red & black wires together. 1 single black . On the connector. The engine connector has. A red & blue together. A single green. then a single blue that goes to the starter. When...
  5. J

    18 Magnum to 20 Command in a 1862.

    Very tired 18 Magnum in 1862. Picked up a Command 20 . I'm look for help in matching up the wiring. The easiest way to splice. Tractor wiring to Commands wiring. What's needed & what may not be needed. I have a motor plate & a drive shaft for it.
  6. J

    1811 with Seized Kohler M18 Engine

    I just saw this. I have an 18 that was out of a 1811. Would need pistons, rings & gaskets to reassembly. Bottom end was in good shape. Cylinders are on the loose side of spec. Long story on how it wound up that way. Lets just say. That person was semi clueless.
  7. J

    Dual action hydraulic cylinder for a 2182 & a Haban 54-inch front mount blade.

    Anyone know where I can get a hydraulic cylinder for the angle adjust for this combo? It now has a manual set up on it. Along with correct hoses & connections? Are Tractor Supplies, cylinders of 8 or 10 inch acceptable replacements?
  8. J

    2182 charging problems ?

    I have a 2182 that has never showed any problems. Went to start, and nothing. Put a voltmeter on battery & only 8 volts. Has only sat for a week. Put another battery in & it started up just as always. Put voltmeter on battery & it's jumping up & down. Not steady at all. As high as 18 volts...
  9. J

    1641to hyd steering.

    Its 1862 then.
  10. J

    1641to hyd steering.

    Sorry. It is an 1862 or1864. Just haven't checked the serial #.
  11. J

    1641to hyd steering.

    I have a 1641 in nice useable condition. I also have a 18?? with hyd steering. It's been used hard & not maintained. The motor is hurt. Would like the hyd steering on the 1641. For those of you in the know. What would be the best way to go about it? Steering tower from 18??& parts to 1641 . Or...
  12. J

    Electric clutch engagement

    Try taking wire plug of switch. Spray with WD40. put back on & off a few times. Get a good connection again. If not try the do same at seat safety switch . Then at connection at PTO.
  13. J

    2084 snowblower width

    I seen that on Face Book . Hope ya got it cheep. It may be better that it look's.
  14. J

    Compression check on 18 magnum.

    Warm Or cold . At least it gave me an outlook that the valves were sealing & it didn't have a hole in a piston. Like I said it had about 70PSI in both cylinders. Air cleaner off & throttle open.
Back
Top