• This community needs YOUR help today. With the ever increasing fees of everything (server, software, domain, e-mail) , we need help. We need more Supporting Members, today. Please invest back into this community to help spread our love and knowledge of IH Cub Cadets. You get a lot of great new account perks including access to private forums. If you sign up for annual, I will ship a few IH Cub Cadet Forum decals too in addition to all the account perks you get. You can see what it looks like below.

    Sign up here: https://www.ihcubcadet.com/account/upgrades

Recent content by dvogtvpe

Shop deals on ebay
cc specialties
shop deals on amazon
cadet connection
IH Cub Cadet Tractor Forum

Help Support IH Cub Cadet Tractor Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. D

    Portage Wisconsin garden tractor daze July 8-9-10

    GT daze is Cub Cadet this year
  2. D

    July 11-14 Portage Garden Tractor Daze

    July 11-14 Portage Wisconsin the annual Garden Tractor Daze at the fairgrounds , great show and lots of garden tractors of all brands . they had just over 500 garden tractors last year . Hope to see you there
  3. D

    2018 Portage GT Daze 7-12 thru 7-15

    Portage WI garden tractor daze 7-12 - 7-15 this show keeps getting bigger every year. last year they hit over 700 garden tractors. all brands welcome . Hope to see you there!
  4. D

    Portage Wi. Garden Tractor Daze

    The annual Garden tractor Daze in Portage WI will be on July 8 to the 10th at the fair grounds . Hope to see allot of Cubs there!
  5. D

    Archive through April 28, 2016

    I bought one of those carbs just to see how they were made. very nicely done . It looks like a Kohler carb kit should work in it for a rebuild. only thing I noticed was the float wasn't set correctly
  6. D

    Archive through August 03, 2014

    this one belongs to a good friend of mine, Bruce Austin from Des Moines. I drove it in spring and finished second at the spring shoot out , I don't like the wing. my head keeps hitting it. hp this one is one of Bruce's to. I drove this allot, won allot of NQS open SS class's with it. 53...
  7. D

    Archive through August 03, 2014

    this is my ride, its been a 50.5 ps/ss all its life till this year. it has a NQS lite pro motor in it for testing now
  8. D

    Archive through July 23, 2015

    its not that difficult, I'll usually gap them at .020 then fine tune it from there. A test light, ohm meter, timing light, continuity light can all be used to set timing just like the point savers little light. Wyatt: looking good!
  9. D

    Archive through August 03, 2014

    typically when the put bike motors in Cubs they use the clutch on the bike motor. they use a live rear axle and run a chain back from the bike trans output sprocket to a sprocket on the rear axle. that's the most common way. if you want to keep the cub tranny then you have to come up with a...
  10. D

    Archive through July 15, 2015

    I swear every tractor I get from Iowa has bent nails instead of cotter pins. hardware stores must not keep cotter pins in stock
  11. D

    Archive through July 15, 2015

    I had a 149 with a nail bent over. what year did they use those?
  12. D

    Portage WI 4th annual garden tractor daze 7-10 - 7-12

    http://www.farmershotline.com/farm-events/4th-annual-garden-tractor-daze-veterans-memorial-field nice all brands show in a real nice location. big swap meet area
  13. D

    Archive through April 27, 2015

    Holden ; a 10 hp engine has a flat oil pan. the 12 and 14 have a little sump on the bottom that you can see from either side, also if you take the air cleaner off you can look in the carb. just above the throttle plate it should say "30" if its a 14. its not guarantee that its a 14 , this stuff...
  14. D

    Archive through April 15, 2015

    bigger the engine is the more they shake. make a 50 cube single. they smooth out when you get them over 7000
  15. D

    Archive through February 21, 2015

    10 and 12 blocks marked 301 on the PTO end are the same. the 14 had its own block. the early 10 hp block without 301 on the PTO end usually can go to a 12 bore. I had one I took to a .090 os 14 bore (3.590). but you do need to take several measurement's down between the cooling fins to make sure...
See more
Back
Top