• This community needs YOUR help today. With the ever increasing fees of everything (server, software, domain, e-mail) , we need help. We need more Supporting Members, today. Please invest back into this community to help spread our love and knowledge of IH Cub Cadets. You get a lot of great new account perks including access to private forums. If you sign up for annual, I will ship a few IH Cub Cadet Forum decals too in addition to all the account perks you get. You can see what it looks like below.

    Sign up here: https://www.ihcubcadet.com/account/upgrades

126 refurb.

IH Cub Cadet Tractor Forum

Help Support IH Cub Cadet Tractor Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.

dschwandt

Well-known member
IHCC Supporter
Joined
Mar 31, 2012
Messages
5,255
Location
Eastern Iowa
displayname
David Schwandt
One of the rare ones finally made it onto the bench the other day.
Will be getting a spring freshen up/clean up and partial refurbish. Re-lined the brake pads.
Have added IH 3 point and spring assist and rebuilt the S/G.
Snugged up the steerimng box and added Heim joints to the tie rod and will "squeeze" the "C" channel and shim the axle to get rid of the "wander"
Engine will be checked out and head pulled for service. Will pull the pan as well and service the breather. Carb has been rebuilt as well
Will be getting tail lights & switch, new driveshaft, coupler, spirol pins and springs as well as resurfaced clutch plates and driver bushing.
Also rebuilding the clutch hanger and support, fixed the cracked headlamp panel and replaced the bulbs w/a matched pair of GE's.

Not going to get carried away with cosmetics though as this will make a great trouble free worker for someone when out the door it goes this spring.
Hopefully, this will assure it's survival in the years to come.
Originally appears to have had an electric lift but someone (not me) replaced it w/a manual setup.

DSCN7737.JPG
DSCN7738.JPG
 

Attachments

  • DSCN7735.JPG
    DSCN7735.JPG
    84.7 KB · Views: 239
  • DSCN7736.JPG
    DSCN7736.JPG
    87.3 KB · Views: 237
Last edited:
Good work! I like your shop set-up!
How did you mount your motor up to work on it? I may copy your set-up if that’s ok!:love::)
 
Good work! I like your shop set-up!
How did you mount your motor up to work on it? I may copy your set-up if that’s ok!:love::)
Justin, It's just a piece of angle drilled to fit the homes where the SG mounts.
Then a piece of tube welded to it with another larger piece to slide into welded to a flat plate that bolts to, the work table is all.
Sane setupworks for all the Kohlers in the NF's and the QL's
 
Justin, It's just a piece of angle drilled to fit the homes where the SG mounts.
Then a piece of tube welded to it with another larger piece to slide into welded to a flat plate that bolts to, the work table is all.
Sane setupworks for all the Kohlers in the NF's and the QL's
Okay! You got a picture?!
 
David, I'll second Marty, nice to see another one being saved.
IH_Thumbs_UP_WHITE.gif
 
David,
What do you do in the area of the clutch arms that rides against the throw-out bearing? Weld it up and grins smooth? Replace the arm??? Just curious. I have welded them up before and it seems to work, but we mostly pull with our tractors so they don't see a lot of hours.
 
Scott, just this morning finished that up.
A little weld on the worn areas, a little time w/an end mill and file and it's hopefully good to go again.

Still have to re-drill the holes in the hanger yet.
I have put a bushing w/grease fitting in some before but its a bear to get those 1/4 bolts/nuts back in place.

DSCN7741.JPG
 
Moving along nicely.
Installed the new driveshaft, coupler, springs, one of the new yokes, new clutch disc and repaired and re-machined throw out lever today.
Also reconnected the saftey neutral start switch that had been disconnected plus a new light switch. The engine is getting new head and pan gasket, front and rear seals as well as new points and plug.
 

Attachments

  • DSCN7836.JPG
    DSCN7836.JPG
    48.4 KB · Views: 190
  • DSCN7837.JPG
    DSCN7837.JPG
    109 KB · Views: 225
  • DSCN7838.JPG
    DSCN7838.JPG
    84.7 KB · Views: 191
Going back together. Not a restoration by any means other than mechanically.
Shimmed the front axle .027" and snugged it right up. Cant stand a wandering Cub!!
Will be put to work pulling a roller around the cemetery over last years new seeding project as soon as it dries up some after the recent rains.

I added headlights, tail lights, 3 point and spring assist.
Plus new brake pads, clutch ass'y w/new disc, spring & driveshaft.

DSCN7859.JPG
DSCN7860.JPG
DSCN7861.JPG
 

Latest posts

Back
Top